T1
티원
NANOSKIN Ultra Line T1 is a professional-grade SiO2-based ceramic serum with a self-leveling formula and a 45-minute flash window that allows relaxed, full-vehicle application. Applied to cars, trucks, boats, and bikes, it creates an ultra-hydrophobic mirror-like coating that delivers strong water, dirt, and UV protection with minimal buffing thanks to a single-towel removal system.
나노스킨 울트라 라인 T1은 자동 레벨링 SiO2 기반 세라믹 세럼으로, 여유로운 전차 도포를 위한 45분의 플래시 타임을 제공합니다. 자동차, 트럭, 보트, 바이크에 초발수 미러 코팅을 형성하며, 한 장의 타월로 마감 가능한 시스템으로 버핑 부담 없이 프로 수준의 결과를 구현합니다.
- Brand
- NANOSKIN
- Categories
- Exterior : Coating
Key features
- Advanced SiO2 technology for professional-grade ceramic protection
- Self-leveling formula for a flat, glossy, streak-free finish
- 45-minute flash window for unhurried full-vehicle application
- Ultra-hydrophobic coating — extreme water beading and contaminant resistance
- One-towel removal system — minimal buffing required
- UV, dirt, and moisture protection after 24-hour cure
- Complete kit: T1 serum, foam applicator, nitrile gloves, microfiber towel
Usage
- Thoroughly wash the vehicle and remove embedded contaminants using a clay bar or light polish to ensure a clean surface.
- Shake the T1 bottle well, then apply a few drops onto the foam applicator or a soft applicator pad.
- Work in small sections, spreading a thin, even coat over paint, glass, or metal surfaces — the self-leveling formula allows coating the entire vehicle before wiping.
- Allow T1 to bond for up to 45 minutes; use this window to cover all panels without rushing.
- Gently wipe off with a clean microfiber towel; lightly buff any remaining streaks with a fresh section of towel.
- Avoid water and harsh conditions for 24 hours to allow full curing.
핵심 특징
- 프로 등급 세라믹 보호를 위한 고급 SiO2 기술
- 평탄하고 광택 있는 얼룩 없는 마감을 위한 자동 레벨링 포뮬라
- 여유 있는 전차 도포를 위한 45분 플래시 타임
- 초발수 코팅 — 강력한 물방울 맺힘 및 오염물 저항
- 원 타월 제거 시스템 — 버핑 최소화
- 24시간 경화 후 UV, 오염, 수분 차단
- 키트 구성: T1 세럼, 폼 어플리케이터, 니트릴 장갑, 마이크로파이버 타월 포함
사용법
- 차량을 깨끗이 세차하고 클레이 바 또는 경질 폴리시로 내장된 오염물을 제거하여 표면을 정리합니다.
- T1 병을 충분히 흔든 후 폼 어플리케이터나 부드러운 패드에 몇 방울 도포합니다.
- 소면적씩 작업하며 도장, 유리, 금속 표면에 얇고 고르게 펴 바릅니다. 자동 레벨링 포뮬라 덕분에 닦기 전 차량 전체를 도포할 수 있습니다.
- T1이 결합되도록 최대 45분간 두고, 서두르지 않고 모든 패널을 코팅합니다.
- 깨끗한 마이크로파이버 타월로 부드럽게 닦아내고, 얼룩이 남으면 새 면으로 가볍게 버핑합니다.
- 완전 경화를 위해 24시간 동안 수분 및 외부 환경 노출을 피합니다.