1K-Nano
1K-나노
Single-component reactive paint sealant that chemically cross-links with cured automotive paint to leave a glass-smooth, deeply glossy finish. Once hardened it resists chemicals, UV exposure and abrasion, replacing the need for a 2K system.
경화된 자동차 도장면과 화학적으로 가교 결합하여 유리처럼 매끈하고 깊은 광택을 남기는 반응성 1액형 실란트입니다. 경화 후에는 화학물질, 자외선, 마모에 강해 2액형 시스템을 대체할 수 있으며 자동차, 상용차, 모터사이클의 완전 경화 도장에 사용됩니다.
- Brand
- Koch Chemie
- Categories
- Exterior : Coating
Key features
- Reactive 1-component sealant
- Glass-smooth deep gloss
- Chemical, UV, abrasion resistant
- Bonds to fully cured paint
- Replaces 2K systems
Usage
- Pre-wash the vehicle with an alkaline product such as Green Star, avoiding sealing shampoos; tackle tar or rust bloom with cleaning clay first.
- Correct any weathering with Heavy Cut and Feinschleifpaste, then refine with Hochglanz-Antihologramm-Politur on an orange anti-hologram pad.
- Wipe each panel with a Profi microfibre soaked in Silicon- & Wachsentferner, follow immediately with a second clean cloth, and put on gloves.
- Working indoors at 15-30 degrees Celsius, decant 1K-Nano into the supplied 75 ml bottle and apply by orbital polisher with a black finishing pad.
- Buff each section for two to three minutes with overlapping passes, then keep polishing without fresh product until a continuous film forms.
- Wait another two to three minutes, then hand-buff the dry film to high gloss with a clean Profi microfibre cloth.
- Allow about one to two hours to harden; do not apply on fresh repair paint, and store the aluminium bottle upright after sealing tightly.
핵심 특징
- 반응성 1액형 실란트
- 유리처럼 매끈한 깊은 광택
- 화학·자외선·마모 저항
- 완전 경화 도장에만 시공
- 2액형 시스템 대체
사용법
- 그린 스타 같은 알칼리성 제품으로 차량을 사전 세차하고 실링 샴푸는 피하며, 타르나 녹꽃은 클레이로 먼저 처리합니다.
- 풍화가 있을 경우 헤비 컷과 파인쉴라이프파스테로 보정한 뒤, 호흐글란츠-안티홀로그람-폴리투어와 오렌지 안티홀로그램 패드로 마무리합니다.
- 각 패널을 실리콘 앤 왁스엔트페어너에 적신 프로피 마이크로파이버로 닦고 바로 새 천으로 한 번 더 닦은 뒤 장갑을 착용합니다.
- 실내 15~30도 환경에서 1K-나노를 동봉된 75 ml 병에 옮긴 다음, 오비탈 폴리셔에 블랙 피니싱 패드를 끼워 도포합니다.
- 한 구역당 2~3분 동안 충분히 겹치며 작업하고, 이후에는 제품을 추가하지 말고 균일한 막이 형성될 때까지 폴리싱합니다.
- 다시 2~3분 기다린 뒤 깨끗한 프로피 마이크로파이버로 마른 도막을 손으로 광택이 날 때까지 닦아냅니다.
- 약 1~2시간 경화시키며 갓 칠한 보수 도장에는 사용하지 않고, 알루미늄 병은 단단히 닫아 세워서 보관합니다.