Graphene Ceramic Spray Coating
그래핀 세라믹 스프레이 코팅
NANOSKIN Graphene Ceramic Spray Coating is a water-based coating formulated with reduced graphene oxide and G-SiO2 polymers that bonds to all exterior surfaces to deliver high gloss, superior hydrophobicity, and up to 12 months of protection. Its mild positive charge helps repel dust through static neutralization, and it can be applied over paint, chrome, glass, headlights, stainless steel, and wheels, as well as interior leather, vinyl, and plastic.
나노스킨 그래핀 세라믹 스프레이 코팅은 환원 그래핀 산화물과 G-SiO2 폴리머를 기반으로 한 수성 코팅제로, 외장의 모든 표면에 결합하여 고광택, 우수한 발수성, 최대 12개월의 보호 기능을 제공합니다. 약한 양전하로 정전기를 중화해 먼지 부착을 억제하며, 도장, 크롬, 유리, 헤드라이트, 스테인리스 스틸, 휠은 물론 실내 가죽, 비닐, 플라스틱에도 사용 가능합니다.
- Brand
- NANOSKIN
- Categories
- Exterior : Coating
Key features
- Reduced graphene oxide and G-SiO2 polymer water-based formula
- Up to 12 months protection with 6-month minimum durability
- Superior hydrophobic water beading and water sheeting
- Mild positive charge repels dust via static neutralization
- Bonds to all exterior surfaces: paint, chrome, glass, wheels, headlights
- Also safe on interior leather, vinyl, and plastic
- Spray-on, wipe-off application over clean, dry surface
Usage
- Wash and dry the vehicle thoroughly to remove all dirt and debris.
- For best results, use a clay bar or AUTOSCRUB surface prep tool to remove embedded contaminants from the finish.
- Spray a fine mist onto one 2'x2' panel at a time or apply directly onto a microfiber towel.
- Spread the coating evenly across the panel, then flip the towel and wipe to remove any excess.
- Buff with a dry microfiber towel in a hashtag pattern to achieve a high-gloss, reflective finish.
- Move to the next 2'x2' section and repeat until all exterior surfaces are coated.
핵심 특징
- 환원 그래핀 산화물과 G-SiO2 폴리머 기반 수성 포뮬라
- 최소 6개월, 최대 12개월 보호 내구성
- 우수한 발수 및 물 흘러내림 효과
- 약한 양전하로 정전기를 중화하여 먼지 부착 억제
- 도장, 크롬, 유리, 휠, 헤드라이트 등 전 외장 표면에 결합
- 실내 가죽, 비닐, 플라스틱에도 안전하게 사용 가능
- 깨끗하고 건조한 표면에 스프레이 후 닦아내는 간편한 사용법
사용법
- 차량을 깨끗이 세차하고 먼지와 이물질을 제거한 뒤 완전히 건조시킵니다.
- 최적의 결과를 위해 클레이 바 또는 오토스크럽 도구로 도장면의 오염물을 먼저 제거합니다.
- 한 번에 약 60×60cm 패널 하나씩 제품을 분사하거나, 마이크로파이버 타월에 직접 뿌립니다.
- 코팅제를 패널 전체에 고르게 펴 바른 후, 타월을 뒤집어 남은 코팅제를 닦아냅니다.
- 건조한 마이크로파이버 타월로 격자 패턴을 그리며 버핑하여 고광택 마무리를 완성합니다.
- 다음 패널로 이동하여 모든 외장 표면이 코팅될 때까지 동일하게 반복합니다.