Spot Remover Body Prep
스팟 리무버 바디 프렙
NANOSKIN Spot Remover / Body Prep is a fast-evaporating solvent cleaner that removes grease, road tar, silicone, wax, and adhesive from vehicle surfaces before painting, coating, or wrapping. VOC-compliant for California and other regulated states, it dries quickly without residue to ensure proper adhesion on painted panels, metal, and primed surfaces.
나노스킨 스팟 리무버 / 바디 프렙은 도장, 코팅 또는 랩 작업 전 차량 표면에서 그리스, 도로 타르, 실리콘, 왁스, 접착제를 제거하는 속건성 용제 세정제입니다. 캘리포니아 및 기타 규제 지역의 VOC 기준을 충족하며, 잔류물 없이 빠르게 건조하여 도장판, 금속, 프라이밍 표면의 접착력을 확보합니다.
- Brand
- NANOSKIN
- Categories
- Exterior : Degreaser&Dewaxing
Key features
- Removes grease, road tar, silicone, wax, and adhesive residues
- Fast-evaporating formula with no smear or film
- VOC-compliant (VOC content: 722 g/L)
- Safe on painted surfaces, metal, and primed panels
- Ready-to-use with no dilution required
- Suitable for detailing bays, collision centers, and fleet shops
Usage
- Park the vehicle in a cool, shaded, well-ventilated area (65–90°F); turn off ignition sources and wear protective gear as needed.
- Mist a light coat onto the target surface, or saturate a clean lint-free microfiber cloth and wipe the area.
- Allow 30–60 seconds for tar, grease, wax, silicone, or adhesive to soften; re-spray if the surface begins to dry.
- Before the solvent evaporates, wipe with a fresh dry microfiber, turning the towel frequently.
- For heavy buildup on rocker panels or wheel arches, rinse with a pressure washer after wiping.
- Let the surface air-dry 10–15 minutes until streak-free; inspect under bright light and re-treat any remaining residue before sanding, priming, or coating.
- Spot test on fresh paint, plastic, or sensitive substrates first; avoid use on hot surfaces or in direct sunlight.
핵심 특징
- 그리스, 도로 타르, 실리콘, 왁스, 접착제 잔류물 제거
- 번짐 또는 피막 없는 속건성 포뮬라
- VOC 기준 적합 (VOC 함량: 722 g/L)
- 도장 표면, 금속, 프라이밍 패널에 안전
- 희석 없이 바로 사용
- 디테일링 베이, 충돌 수리 센터, 플리트 업체 적합
사용법
- 서늘하고 그늘진 환기가 잘 되는 장소(18~32°C)에 차량을 세우고, 발화원을 차단하며 필요 시 보호장구를 착용합니다.
- 대상 표면에 가볍게 분사하거나, 깨끗한 극세사 천에 충분히 적셔 닦아냅니다.
- 타르, 그리스, 왁스, 실리콘, 접착제가 부드러워지도록 30~60초 유지하고, 건조되기 시작하면 재분사합니다.
- 용제가 완전히 증발하기 전, 새 극세사 천으로 면을 자주 바꿔가며 닦아냅니다.
- 사이드실 패널이나 휠 아치 등 오염이 심한 부위는 닦은 후 고압수로 헹굽니다.
- 10~15분 건조 후 밝은 조명 아래서 얼룩 없는지 확인하고, 연마·프라이밍·코팅 전 잔여 오염물을 재처리합니다.
- 새 도장, 플라스틱, 민감한 소재는 먼저 눈에 띄지 않는 부위에서 테스트하고, 뜨거운 표면이나 직사광선 아래서는 사용을 피합니다.