HYPER DRESS
하이퍼 드레스
NANOSKIN HYPER DRESS is a hyper-concentrated water-based silicone dressing that restores and protects rubber, vinyl, and plastic surfaces on both the interior and exterior of vehicles. Dilutable from 1:1 down to 1:4 with water, it delivers a gloss finish ranging from high gloss to a natural satin appearance, while UV-protective ingredients guard against fading, cracking, and surface degradation.
나노스킨 하이퍼 드레스는 차량 내외부의 고무, 비닐, 플라스틱 표면을 복원하고 보호하는 초고농축 수성 실리콘 드레싱입니다. 물과 1:1~1:4 비율로 희석하여 하이 글로스부터 내추럴 새틴까지 다양한 광택을 구현하며, UV 차단 성분이 퇴색, 균열, 표면 손상을 방지합니다.
- Brand
- NANOSKIN
- Categories
- Exterior : Tire&Wheel Sealant, Interior : Trim Sealants
- Primary dilution
- 1:1~1:4
Key features
- Hyper-concentrated formula — dilutable 1:1 to 1:4 for varying gloss levels
- Water-based silicone emulsion for interior and exterior use
- Restores rubber, vinyl, and plastic to OEM-like appearance
- UV protection prevents fading, cracking, and surface degradation
- Dry-to-touch finish on interior trim and door panels
- Minimal dirt and dust attraction after application
- Safe on non-painted engine plastics and wheel wells
Dilution
- Exterior : Tire&Wheel Sealant — 1:1~1:4 (1:1-4) (primary)
Usage
- Clean the tire or surface thoroughly, removing dust, dirt, and any previously applied dressing.
- Pour HYPER DRESS into a sprayer bottle and dilute with water to the desired gloss level: 1:1 for high gloss, 1:2 for medium gloss, 1:3 for satin finish, or 1:4 for a natural finish.
- Spray a generous amount onto an applicator pad, then spread evenly over the entire surface.
- If needed, spray additional product directly onto the surface, then allow to dry to a shine.
핵심 특징
- 초고농축 포뮬라 — 1:1~1:4 희석으로 다양한 광택 조절 가능
- 내외부 사용에 적합한 수성 실리콘 에멀전
- 고무, 비닐, 플라스틱을 OEM 수준의 외관으로 복원
- UV 차단으로 퇴색, 균열, 표면 손상 방지
- 인테리어 트림 및 도어 패널에 건조 후 비점착 마감
- 도포 후 먼지와 이물질 흡착 최소화
- 미도장 엔진 플라스틱 및 휠 하우스에도 안전
사용법
- 타이어나 표면을 깨끗이 세척하여 먼지, 오염물, 기존 드레싱을 제거합니다.
- 하이퍼 드레스를 스프레이 병에 담고 원하는 광택 수준에 맞게 물로 희석합니다: 1:1 하이 글로스, 1:2 미디엄 글로스, 1:3 새틴 피니시, 1:4 내추럴 피니시.
- 어플리케이터 패드에 충분한 양을 분사한 후 표면 전체에 고르게 펴 바릅니다.
- 필요한 경우 표면에 추가로 분사하고 광택이 날 때까지 건조시킵니다.