NANOSKIN 스팟 리무버 바디 프렙 희석비 & 사용 가이드

NANOSKIN 스팟 리무버 바디 프렙 희석비 pH 스펙 카드

Spot Remover Body Prep

스팟 리무버/바디 프렙은 도장, 코팅, 랩 작업 전 차량 표면에서 그리스, 도로 타르, 실리콘, 왁스, 접착제를 제거하는 속건성 용제 세정제입니다. 캘리포니아 등 규제 지역의 VOC 기준을 충족하며, 잔류물 없이 빠르게 건조해 도장 패널·금속·프라이밍 표면의 접착력 확보에 도움을 줍니다.

브랜드
NANOSKIN
카테고리
Exterior : Degreaser&Dewaxing
기본 희석 비율
RTU
최종 업데이트
2026-06-02

핵심 특징

희석 비율

용도희석비율
Exterior : Degreaser&Dewaxing (기본)RTU1:0

사용법

  1. 서늘하고 그늘진 환기가 잘 되는 장소(18~32°C)에 차량을 세우고 발화원을 차단하며 필요 시 보호장구를 착용합니다.
  2. 대상 표면에 가볍게 분사하거나 깨끗한 보풀 없는 극세사 천에 충분히 적셔 닦아냅니다.
  3. 타르·그리스·왁스·실리콘·접착제가 부드러워지도록 30~60초 유지하고, 표면이 마르기 시작하면 재분사합니다.
  4. 용제가 완전히 증발하기 전, 새 극세사 천으로 면을 자주 바꿔 가며 닦아냅니다.
  5. 사이드실 패널이나 휠 아치 등 오염이 심한 부위는 닦아낸 뒤 고압수로 헹굽니다.
  6. 10~15분 건조 후 밝은 조명 아래에서 얼룩 여부를 확인하고, 연마·프라이밍·코팅 전 잔여물을 재처리합니다.
  7. 새 도장·플라스틱·민감한 소재는 먼저 잘 보이지 않는 부위에서 테스트하고, 뜨거운 표면이나 직사광선 아래에서는 사용을 피합니다.

Spot Remover / Body Prep is a fast-evaporating solvent cleaner that removes grease, road tar, silicone, wax and adhesive from vehicle surfaces before painting, coating or wrapping. It is VOC-compliant for California and other regulated states and dries quickly without residue to support proper adhesion on painted panels, metal and primed surfaces.

Key features

  • Removes grease, road tar, silicone, wax and adhesive residues
  • Fast-evaporating with no smear or film
  • VOC-compliant (VOC content: 722 g/L)
  • Suitable for painted surfaces, metal and primed panels
  • Ready-to-use with no dilution required
  • Suited to detailing bays, collision centers and fleet shops

Usage

  1. Park the vehicle in a cool, shaded, well-ventilated area (65 to 90 deg F); turn off ignition sources and wear protective gear as needed.
  2. Mist a light coat onto the target surface, or saturate a clean lint-free microfiber cloth and wipe the area.
  3. Allow 30 to 60 seconds for tar, grease, wax, silicone or adhesive to soften; re-spray if the surface starts to dry.
  4. Before the solvent evaporates, wipe with a fresh dry microfiber and turn the towel frequently.
  5. For heavy buildup on rocker panels or wheel arches, rinse with a pressure washer after wiping.
  6. Let the surface air-dry 10 to 15 minutes until streak-free, then inspect under bright light and re-treat any remaining residue before sanding, priming or coating.
  7. Spot test on fresh paint, plastic or sensitive substrates first; avoid use on hot surfaces or in direct sunlight.

다른 이름: 나노스킨, NANOSKIN Spot Remover Body Prep, NS Spot Remover Body Prep, SRRBP, NANOSKIN SRRBP, NS SRRBP, 나노스킨 스팟 리무버 바디 프렙, 나노스킨 SRRBP, NA-SRR128

View in English

출처

관련 제품

NANOSKIN의 다른 제품

같은 카테고리(Degreaser&Dewaxing) 제품

더 보기