PERFECTA SIO2 - Ceramic quick detailer
페르펙타 SIO2 - 세라믹 퀵 디테일러
PERFECTA SIO2 is a ceramic-style quick detailer from Labocosmetica that pairs SiO2 and TiO2 polymers for lasting hydrophobic protection, chemical resistance, and added gloss. Used as a topper it extends the beading and sheeting of waxes, sealants, or coatings while building an antistatic self-cleaning layer. It can also work as a standalone detailer and holds up to about three neutral-shampoo washes.
PERFECTA SIO2는 SiO2와 TiO2 폴리머를 결합한 라보코스메티카의 세라믹 퀵 디테일러로, 발수 보호와 화학 저항성, 광택을 함께 제공합니다. 토퍼로 쓰면 왁스·실런트·코팅의 비딩과 시팅을 연장하면서 정전기 방지·셀프 클리닝 막을 형성합니다. 단독 디테일러로도 사용할 수 있으며 중성 샴푸 세차 기준 약 3회 정도 효과가 유지됩니다.
- Brand
- Labocosmetica
- Categories
- Exterior : Quick Detailer, Exterior : Coating
Key features
- Extends beading and sheeting on waxes, sealants, and SiO2 coatings
- Doubles as a quick detailer or ceramic spray
- Holds up to about three neutral-shampoo washes
- SiO2 boosts water repellency and gloss; TiO2 adds resistance to acid rain, water spots, and UV
- Antistatic self-cleaning layer cuts dust and dirt pickup
- Glass-like gloss that highlights paint depth
Usage
- Wash the car and remove iron and mineral fallout with SIDERO, shake the bottle well, and work no more than about half a square meter at a time.
- On dry paint, mist onto panel or short-pile microfiber, spread, then finish with a clean long-pile microfiber, using about two sprays for small areas.
- On wet paint, spray directly onto bodywork and work it in with a SUPER DRYER microfiber using about two to three sprays per section.
- Buff to a high-mirror finish with a clean microfiber, keep water off for at least about 12 hours, full cure around 12 hours, allow about 24 hours before a second layer, and avoid use above about 25 degrees C or in direct sun.
핵심 특징
- 왁스·실런트·SiO2 코팅 위 비딩·시팅 연장
- 퀵 디테일러 겸 세라믹 스프레이로 사용
- 중성 샴푸 세차 기준 약 3회까지 효과 유지
- SiO2로 발수성·광택 강화, TiO2로 산성비·워터스팟·UV 저항
- 정전기 방지 셀프 클리닝 막으로 먼지·오염 부착 감소
- 도장 깊이감을 살리는 유리 같은 광택
사용법
- 차량을 세차한 뒤 SIDERO로 철분과 미네랄 오염을 제거하고, 병을 잘 흔들어 한 번에 약 0.5 제곱미터까지만 작업합니다.
- 마른 도장에서는 도장면 또는 단모 마이크로파이버에 분사한 뒤 펴 바르고, 좁은 구역은 약 2회 분사로 충분하며 깨끗한 장모 마이크로파이버로 마감합니다.
- 젖은 도장에서는 도장면에 직접 분사한 뒤 SUPER DRYER 마이크로파이버로 구역당 약 2에서 3회 분사 분량으로 펴 바릅니다.
- 깨끗한 마이크로파이버로 미러 마감까지 버핑하며, 약 12시간 이상 물을 피하고 추가 도포는 약 24시간 후, 25도씨 이상이나 직사광선에서는 사용하지 않습니다.