100% Degreasing
100% 디그리싱
innova · 이노바 · 이노바카 · Innovacar 100% Degreasing · IC 100% Degreasing · 100D · Innovacar 100D · IC 100D · 이노바카 100% 디그리싱 · 이노바카 100D · 79406
A concentrated multi-purpose degreaser that pairs chelating and colloidal action to loosen oils, grease, and heavy soil across vehicle surfaces. It contains no sodium hydroxide, phosphorus, EDTA, or NTA, so it stays gentle on coatings, plastics, and seals while leaving an antistatic, dust-repellent finish.
킬레이팅과 콜로이드 작용을 결합해 차량 표면의 오일, 그리스, 심한 오염을 풀어내는 농축 다목적 탈지제입니다. 수산화나트륨·인·EDTA·NTA를 넣지 않아 코팅·플라스틱·고무 패킹에 순하며 대전 방지와 방진 효과를 남깁니다.
- Brand
- Innova Car
- Categories
- Exterior : Degreaser&Dewaxing
- Primary dilution
- 1:2~1:3
- pH
- alkali (10)
Key features
- Multi-surface degreaser
- Chelating action for metal and rim cleaning
- Colloidal formula for oil and grease penetration
- Antistatic and dust-repellent finish
- Plant-derived surfactants
- No sodium hydroxide, phosphorus, EDTA, or NTA
- Concentrated, effective in small amounts
- Gentle on coatings and delicate materials
Dilution
- Exterior : Degreaser&Dewaxing — 1:2~1:3 (1:2-3) (primary)
Usage
- For rims, tyres, engine, and interior hard surfaces, dilute 1:2 to 1:3, spray, and let it dwell a couple of minutes; scrub heavy soil with a nylon brush, then rinse or wipe with a damp microfibre cloth.
- For pre-wash with a pump or bucket, dilute 1:20 to 1:30 and spray the vehicle before the main wash.
- For pre-wash via foam lance or gun, use concentrated up to 1:2 through the lance; delivered dilution varies by setup.
- For routine interior hard plastics, dilute 1:10 to 1:20, vacuum dust first, then apply and wipe with a soft damp cloth.
- For routine fabric and upholstery, dilute 1:5 to 1:40 by soil level, apply, agitate if needed, then wipe or extract.
- Do not apply to hot surfaces, and test delicate materials on a hidden area first.
핵심 특징
- 다목적 표면 탈지제
- 금속·휠 세정을 위한 킬레이팅 작용
- 오일·그리스 침투를 돕는 콜로이드 처방
- 대전 방지·방진 마무리
- 식물성 유래 계면활성제
- 수산화나트륨·인·EDTA·NTA 미함유
- 소량으로 효과적인 농축 제형
- 코팅과 섬세한 소재에 순함
사용법
- 휠·타이어·엔진·실내 하드 표면은 1:2~1:3으로 희석해 분사하고 잠시 방치한 뒤, 심한 오염은 나일론 브러시로 문질러 헹구거나 젖은 마이크로파이버 천으로 닦습니다.
- 펌프나 버킷 프리워시는 1:20~1:30으로 희석해 본 세차 전 차량에 분사합니다.
- 폼 랜스나 폼 건 프리워시는 원액~1:2 농도로 랜스를 통해 사용하며 실제 희석비는 장비에 따라 달라집니다.
- 실내 하드 플라스틱 일상 세정은 1:10~1:20으로 희석해 먼지를 진공 제거한 뒤 부드러운 젖은 천으로 닦습니다.
- 패브릭·내장재 일상 세정은 오염 정도에 따라 1:5~1:40으로 희석해 도포하고 필요 시 문질러 닦거나 추출합니다.
- 뜨거운 표면에는 쓰지 말고 섬세한 소재는 눈에 띄지 않는 부위에서 먼저 테스트합니다.