F1 Force One
에프원 포스 원
innova · 이노바 · 이노바카 · Innovacar F1 Force One · IC F1 Force One · F1FO · Innovacar F1FO · IC F1FO · 이노바카 에프원 포스 원 · 이노바카 F1FO · 79186
A heavy-cut compound formulated as a silicone-free abrasive paste for deep scratches and severe paint defects. Its breaking-down grain delivers strong abrasive force that eases off as the grains fracture under friction, making it effective on hard paint and deep sanding marks up to grit 1500. It suits both rotary and rotary-orbital polishers.
깊은 스크래치와 심한 도장 결함을 위한 실리콘 미함유 고절삭 컴파운드입니다. 파쇄형 입자가 마찰로 부서지며 점차 약해지는 강한 연마력을 내, 경질 도장면과 1500방까지의 깊은 샌딩 자국에 효과적입니다. 회전식·회전 궤도식 광택기 모두에 맞습니다.
- Brand
- Innova Car
- Categories
- Exterior : Polishes
Key features
- Heavy-cut compound for deep scratches and hard paint
- Breaking-down grain for strong cutting power
- Silicone-free, suitable before coating
- Removes sanding damage up to grit 1500
- Suited to acid rain damage and deep oxidation
- Works with rotary and rotary-orbital polishers
Usage
- Finish all pre-polishing steps: pre-wash, wash, and chemical and mechanical decontamination.
- Shake the product well before use.
- Fit the pad firmly and centrally on the polisher plate.
- Apply product to a hard white sponge pad, or a wool pad for maximum cut; use more on a new pad and make sure a used pad is clean.
- Drape the cable over your shoulder to prevent bodywork damage.
- Start and stop the polisher with the pad on the surface to avoid splashing.
- Polish at 800 rpm over roughly 60x40 cm, horizontally then vertically, overlapping each pass by half.
- Raise the speed toward 2000 rpm and re-treat the area for uniform coverage.
- Remove excess with a microfibre cloth and check the result with D2 Check.
- Work across all areas chosen for polishing.
- Reassess the surface to decide on an intermediate step with A1 All In One, or go straight to finishing with P1 Polish Up.
핵심 특징
- 깊은 스크래치와 경질 도장용 고절삭 컴파운드
- 강한 연마력을 위한 파쇄형 입자
- 실리콘 미함유, 코팅 전처리에 적합
- 1500방까지의 샌딩 손상 제거
- 산성비 손상과 깊은 산화에 적합
- 회전식·회전 궤도식 광택기 호환
사용법
- 프리워시·세차·화학적·기계적 오염 제거 등 폴리싱 전 단계를 모두 마칩니다.
- 사용 전 제품을 충분히 흔듭니다.
- 패드를 폴리셔 플레이트 정중앙에 단단히 부착합니다.
- 경질 화이트 스펀지 패드(최대 절삭은 울 패드)에 제품을 도포합니다. 새 패드는 더 많이, 사용 패드는 깨끗해야 합니다.
- 도장면 손상을 막기 위해 케이블을 어깨에 걸칩니다.
- 튐을 막기 위해 패드를 표면에 댄 채 전원을 켜고 끕니다.
- 800 rpm으로 약 60x40 cm를 수평·수직으로 50% 겹쳐 작업합니다.
- 속도를 2000 rpm까지 올리며 같은 구역을 다시 작업해 균일하게 덮습니다.
- 마이크로파이버 천과 D2 체크로 잔여물을 제거하며 결과를 확인합니다.
- 작업하려는 모든 구역에 동일하게 진행합니다.
- 표면을 다시 평가해 A1 올인원으로 중간 단계를 거칠지, P1 폴리시 업으로 바로 마무리할지 정합니다.