EXOv5 Ultra Durable Hydrophobic Coating
EXOv5 울트라 듀러블 하이드로포빅 코팅
EXOv5 forms a hard film that makes water spots easier to remove, resists wash chemicals, and helps protect against micro-marring. The finish is high-gloss, warm-toned, and strongly hydrophobic, with a single application typically lasting up to about two years. EXOv5 can be used standalone or as a top layer over C1 Crystal Lacquer or Crystal Serum Light.
EXOv5는 워터 스팟 제거가 수월한 단단한 막을 형성하고 세차용 화학제에 강하며 미세 마링도 막아주는 코팅입니다. 1회 도포로 최대 약 2년 지속되는 따뜻한 톤의 고광택, 강한 발수 마감을 만듭니다. 단독 실런트로도 사용할 수 있고 C1 크리스탈 라커나 크리스탈 세럼 라이트의 탑코트로도 적층할 수 있습니다.
- Brand
- GTECHNIQ
- Categories
- Exterior : Coating
Key features
- Single-layer application
- About 18 to 24 months of durability
- Easier application
- Adds gloss with water and dirt repellency
Usage
- Use EXOv5 alone or over C1 or CSL; for soft or dark paint a C1 or CSL base coat is recommended.
- When layering over C1, apply EXOv5 at least 4 hours but within 12 hours of finishing C1.
- Over CSL, apply EXOv5 right after CSL or wait about 2 hours for a longer flash-off.
- Keep the vehicle out of direct sunlight, above 5 degrees Celsius, fully dry, and keep it dry for at least 12 hours after.
- Wipe surfaces with Gtechniq Panel Wipe on an MF1 ZeroR cloth (apply to the cloth, not the panel); skip this step if applying over freshly cured C1 or CSL.
- Shake the bottle and wear gloves.
- Prime the AP2 Ultra Soft Foam applicator until evenly damp.
- Apply in overlapping strokes per small panel or per half of a large panel; remove residue immediately with an MF1, then follow with a second MF1 to clear smearing.
- Cure for at least 12 hours before getting wet.
- Avoid washing the car for at least a week after application.
- Store in a cool, dry place.
- Use within 3 months of opening.
핵심 특징
- 1회 도포
- 약 18~24개월 지속
- 쉬운 시공성
- 광택과 발수·방오 성능 부여
사용법
- EXOv5는 단독으로 사용하거나 C1·CSL 위에 적층하며, 스크래치에 약하거나 어두운 도장에는 C1 또는 CSL을 베이스코트로 권장합니다.
- C1 위에 도포할 때는 C1 시공 후 최소 4시간, 12시간 이내에 도포합니다.
- CSL 위에 도포할 때는 곧바로 시공하거나 플래시 오프를 위해 약 2시간 기다린 후 도포합니다.
- 차량을 직사광선이 없는 곳에 두고 5°C 이상, 완전 건조 상태로 시공하며 시공 후 최소 12시간 동안 건조 상태를 유지합니다.
- Gtechniq Panel Wipe를 MF1 ZeroR 천에 분무해 모든 표면을 닦습니다(패널에 직접 분사하지 않음). 갓 시공한 C1·CSL 위에 도포할 때는 생략합니다.
- 병을 잘 흔들고 장갑을 착용합니다.
- AP2 울트라 소프트 폼 어플리케이터에 제품을 고르게 적셔 패드가 촉촉해지게 합니다.
- 작은 패널 또는 큰 패널 절반씩 겹쳐 도포하고, 즉시 MF1 천으로 잔여물을 제거한 뒤 두 번째 MF1으로 얼룩을 마무리합니다.
- 도포 후 최소 12시간 동안 물에 닿지 않게 경화시킵니다.
- 도포 후 최소 1주일간 세차하지 않을 것을 권장합니다.
- 서늘하고 건조한 곳에 보관합니다.
- 개봉 후 3개월 이내에 사용합니다.