Crystal Serum Light
크리스탈 세럼 라이트
Crystal Serum Light is a silicon-dioxide-based ceramic coating that bonds with the clear coat to create a chemically resistant, high-gloss layer. It defends paint against swirl marks, bird droppings, UV exposure, and water spots, and offers up to about five years of protection when properly maintained.
크리스탈 세럼 라이트는 이산화규소(SiO2) 기반의 세라믹 코팅으로, 클리어코트와 결합해 내화학성과 고광택을 갖춘 보호막을 형성합니다. 스월 마크, 새 배설물, 자외선, 워터 스팟으로부터 도장을 보호하며, 적절히 관리하면 최대 약 5년까지 지속됩니다.
- Brand
- GTECHNIQ
- Categories
- Exterior : Coating
Key features
- Swirl and chemical resistance
- High gloss
- Up to about five years of durability
Usage
- Apply indoors and keep the vehicle indoors for 12 hours afterwards, away from direct sunlight.
- Apply only at temperatures between 5 and 25 degrees Celsius.
- Shake well and wear gloves.
- Wash and decontaminate the paint thoroughly first, polishing if needed to remove imperfections.
- Spray Panel Wipe onto a Gtechniq MF1 cloth and wipe each panel in small sections.
- Soak the application pad with three full pipette measures of CSL and work the liquid evenly into the pad.
- Cap the bottle and set it aside; holding it warms the product and speeds curing.
- Apply in overlapping strokes over an area roughly 2ft by 2ft or along body lines.
- Remove residue immediately with an MF1 cloth, using two cloths in rotation and avoiding heavy pressure.
- Inspect the panel under bright, diffused light for any remaining residue.
- If residue cures fully, polish the area and reapply CSL.
- When done, soak the cloths in water and wash and dry them as soon as possible.
- Wait about 2 hours before topping with EXO Ultra Durable or C2 Liquid Crystal.
- Store in a cool, dry place.
- Use within 3 months of opening.
핵심 특징
- 스월 및 화학 저항성
- 고광택 마감
- 최대 약 5년 내구성
사용법
- 실내에서 시공하고, 시공 후 12시간은 차량을 실내에 두며 직사광선을 피합니다.
- 5°C에서 25°C 사이의 온도에서만 시공합니다.
- 잘 흔들고 장갑을 착용합니다.
- 도장면을 철저히 세차·제염하고 필요 시 폴리싱으로 결함을 제거합니다.
- Panel Wipe를 Gtechniq MF1 천에 분무한 뒤 패널을 작은 부분씩 닦아냅니다.
- 피펫으로 CSL을 3정량씩 어플리케이션 패드에 적시고 고르게 스미게 합니다.
- 병 뚜껑을 닫아 한쪽에 두며, 손에 들고 있으면 조기 경화될 수 있으니 주의합니다.
- 약 2ft x 2ft 면적이나 차체 라인을 따라 겹쳐 도포합니다.
- 즉시 MF1 천으로 잔여물을 제거하며, 두 장을 번갈아 사용하고 강한 힘은 피합니다.
- 밝고 분산된 조명으로 잔여물이 남았는지 확인합니다.
- 잔여물이 완전히 경화되었다면 해당 부위를 폴리싱하고 CSL을 재시공합니다.
- 작업 후 즉시 천을 물에 담가 빠르게 세척하고 건조합니다.
- 약 2시간 기다린 후 EXO 또는 C2 리퀴드 크리스탈을 도포합니다.
- 서늘하고 건조한 곳에 보관합니다.
- 개봉 후 3개월 이내에 사용합니다.