GTECHNIQ EXOv5 울트라 듀러블 하이드로포빅 코팅 희석비 & 사용 가이드

GTECHNIQ EXOv5 울트라 듀러블 하이드로포빅 코팅 희석비 pH 스펙 카드

EXOv5 Ultra Durable Hydrophobic Coating

EXOv5는 워터 스팟 제거가 수월한 단단한 막을 형성하고 세차용 화학제에 강하며 미세 마링도 막아주는 코팅입니다. 1회 도포로 최대 약 2년 지속되는 따뜻한 톤의 고광택, 강한 발수 마감을 만듭니다. 단독 실런트로도 사용할 수 있고 C1 크리스탈 라커나 크리스탈 세럼 라이트의 탑코트로도 적층할 수 있습니다.

브랜드
GTECHNIQ
카테고리
Exterior : Coating
기본 희석 비율
RTU
최종 업데이트
2026-06-18

핵심 특징

희석 비율

용도희석비율
Exterior : Coating (기본)RTU1:0

사용법

  1. EXOv5는 단독으로 사용하거나 C1·CSL 위에 적층하며, 스크래치에 약하거나 어두운 도장에는 C1 또는 CSL을 베이스코트로 권장합니다.
  2. C1 위에 도포할 때는 C1 시공 후 최소 4시간, 12시간 이내에 도포합니다.
  3. CSL 위에 도포할 때는 곧바로 시공하거나 플래시 오프를 위해 약 2시간 기다린 후 도포합니다.
  4. 차량을 직사광선이 없는 곳에 두고 5°C 이상, 완전 건조 상태로 시공하며 시공 후 최소 12시간 동안 건조 상태를 유지합니다.
  5. Gtechniq Panel Wipe를 MF1 ZeroR 천에 분무해 모든 표면을 닦습니다(패널에 직접 분사하지 않음). 갓 시공한 C1·CSL 위에 도포할 때는 생략합니다.
  6. 병을 잘 흔들고 장갑을 착용합니다.
  7. AP2 울트라 소프트 폼 어플리케이터에 제품을 고르게 적셔 패드가 촉촉해지게 합니다.
  8. 작은 패널 또는 큰 패널 절반씩 겹쳐 도포하고, 즉시 MF1 천으로 잔여물을 제거한 뒤 두 번째 MF1으로 얼룩을 마무리합니다.
  9. 도포 후 최소 12시간 동안 물에 닿지 않게 경화시킵니다.
  10. 도포 후 최소 1주일간 세차하지 않을 것을 권장합니다.
  11. 서늘하고 건조한 곳에 보관합니다.
  12. 개봉 후 3개월 이내에 사용합니다.

EXOv5 forms a hard film that makes water spots easier to remove, resists wash chemicals, and helps protect against micro-marring. The finish is high-gloss, warm-toned, and strongly hydrophobic, with a single application typically lasting up to about two years. EXOv5 can be used standalone or as a top layer over C1 Crystal Lacquer or Crystal Serum Light.

Key features

  • Single-layer application
  • About 18 to 24 months of durability
  • Easier application
  • Adds gloss with water and dirt repellency
  • 115° water contact angle

Usage

  1. Use EXOv5 alone or over C1 or CSL; for soft or dark paint a C1 or CSL base coat is recommended.
  2. When layering over C1, apply EXOv5 at least 4 hours but within 12 hours of finishing C1.
  3. Over CSL, apply EXOv5 right after CSL or wait about 2 hours for a longer flash-off.
  4. Keep the vehicle out of direct sunlight, above 5 degrees Celsius, fully dry, and keep it dry for at least 12 hours after.
  5. Wipe surfaces with Gtechniq Panel Wipe on an MF1 ZeroR cloth (apply to the cloth, not the panel); skip this step if applying over freshly cured C1 or CSL.
  6. Shake the bottle and wear gloves.
  7. Prime the AP2 Ultra Soft Foam applicator until evenly damp.
  8. Apply in overlapping strokes per small panel or per half of a large panel; remove residue immediately with an MF1, then follow with a second MF1 to clear smearing.
  9. Cure for at least 12 hours before getting wet.
  10. Avoid washing the car for at least a week after application.
  11. Store in a cool, dry place.
  12. Use within 3 months of opening.

다른 이름: 지테크닉, G-technique, g techniq, EXOv5, EXO v5, EXO, Gtechniq EXOv5, Gtechniq EXO, 지테크닉 EXOv5, 지테크닉 EXO, 엑소 v5, 엑소

View in English

출처

관련 제품

GTECHNIQ의 다른 제품

같은 카테고리(Coating) 제품

더 보기