Coat Ultima HSH-Technology
코트 울티마 HSH-테크놀로지
serv · 서브페이스 · 서브 · servFaces Coat Ultima HSH-Technology · SF Coat Ultima HSH-Technology · Coat Ultima · CUHSH · servFaces CUHSH · SF CUHSH · 서브페이시스 코트 울티마 HSH-테크놀로지 · SF10004.1
A hybrid silicon/polymer hard coating that gives painted surfaces lasting protection. Its molecular-matrix structure forms an ultra-thin, non-stick layer with strong hardness, dirt repellency, and added gloss. The particles bond chemically to the surface and help guard against oxidation, salt, insects, and micro-scratches.
도장면을 오래 보호하는 하이브리드 실리콘/폴리머 하드 코팅입니다. 분자 매트릭스 구조가 초박막 논스틱 층을 만들어 단단함과 오염 차단, 광택을 더해 줍니다. 입자가 표면에 화학적으로 결합해 산화와 염분, 벌레 오염, 미세 스크래치로부터 도장을 지켜 줍니다.
- Brand
- servFaces
- Categories
- Exterior : Coating
Key features
- Hybrid silicon/polymer molecular-matrix structure
- Non-stick ultra-thin hard-coat layer
- About 60 to 65 percent harder than conventional clear coat
- Protection against oxidation, salt, and insects
- Fewer micro-scratches from hand washing
- Chemical resistance across pH 2 to 13
- Yellowing-proof and abrasion resistant
- Gloss guarantee of 5 to 10 years for professional use
Usage
- Clean the surface with Surface Cleaner Ultima, then neutralize with Surface Cleaner Neutra.
- Place the application cloth onto the applicator block.
- Apply 12–18 drops to the cloth and spread quickly across the surface panel by panel, covering a maximum of half a hood per application until a visible film forms.
- Allow to dry for approximately 1–3 minutes depending on humidity, temperature, and quantity applied.
- Remove excess with the first Special Coating Towel, working from the edges inward using straight, swift movements.
- Buff with a fresh Special Coating Towel using light circular pressure, working from edges inward.
- If streaks remain, use another clean towel and repeat until no streaks are visible (verify with a light source).
- Recoating is possible after 20 minutes but must be completed within 35 minutes.
핵심 특징
- 하이브리드 실리콘/폴리머 분자 매트릭스 구조
- 논스틱 초박막 하드 코트 층
- 일반 클리어 코트 대비 약 60~65% 높은 경도
- 산화, 염분, 벌레 오염으로부터 보호
- 손 세차로 인한 미세 스크래치 감소
- pH 2~13 범위의 화학 저항성
- 황변 방지 및 내마모성
- 전문가 사용 기준 5~10년 광택 보증
사용법
- Surface Cleaner Ultima로 표면을 세정한 후 Surface Cleaner Neutra로 중화합니다.
- 어플리케이터 블록에 도포용 천을 올려 놓습니다.
- 천에 12~18방울을 떨어뜨린 뒤 패널 단위로 눈에 보이는 피막이 생길 때까지 빠르게 펴 바르고, 한 번에 최대 후드 절반 면적을 넘지 않도록 합니다.
- 습도, 온도, 도포량에 따라 약 1~3분간 건조시킵니다.
- 첫 번째 Special Coating Towel로 가장자리부터 중앙 방향으로 직선 동작을 이용해 잉여 제품을 제거합니다.
- 새로운 Special Coating Towel로 가장자리부터 중앙 방향으로 원형 동작을 이용해 가볍게 버핑합니다.
- 얼룩이 남아 있으면 새 타월로 반복하고, 광원으로 확인하면서 작업합니다.
- 재코팅은 20분 후 가능하며, 35분 이내에 완료해야 합니다.