Ceramic Coat Rims Matt
세라믹 코트 림스 매트
serv · 서브페이스 · 서브 · servFaces Ceramic Coat Rims Matt · SF Ceramic Coat Rims Matt · CCRM · servFaces CCRM · SF CCRM · 서브페이시스 세라믹 코트 림스 매트 · SF10182.2
A transparent, high-strength ceramic coating that gives wheels a semi-gloss finish on painted and unpainted rims. It builds a durable, dirt-resistant film rated to withstand heat up to +1050C and shields against brake-fluid attack through its special resin. The flexible layer bonds at up to 8 um without chipping or peeling.
휠 표면을 반광으로 마감하는 투명 고강도 세라믹 코팅으로, 도장 및 비도장 림에 모두 사용합니다. 오염에 강한 내구성 피막을 만들고 최대 +1050C의 열을 견디며, 특수 수지가 브레이크 오일로 인한 손상을 막아 줍니다. 최대 8um 두께로 유연하게 밀착되어 박리나 탈락이 없습니다.
- Brand
- servFaces
- Categories
- Exterior : Tire&Wheel Sealant
Key features
- Semi-gloss finish for painted and unpainted rims
- Heat resistance up to +1050C
- Brake-fluid resistance from special resin
- Flexible film up to 8 um without chipping or peeling
- Not removable by conventional cleaners
- Long-lasting dirt-resistant film
- Low product consumption
Usage
- Clean the surface with Surface Cleaner Ultima, then neutralize with Surface Cleaner Neutra.
- Place the application cloth onto the applicator block.
- Apply 12–18 drops of product onto the cloth and spread quickly across the surface in sections of max. 50×50 cm until a visible film forms.
- Allow to dry for approximately 1–3 minutes, adjusting for humidity and temperature.
- Remove excess material with a Special Coating Towel, working from the edges inward using straight, swift motions.
- Buff with a fresh Special Coating Towel using light circular pressure, working from edges inward.
- If streaks remain, use another clean towel and repeat until the surface is clear (verify with a light source).
- Recoating is possible after 20 minutes but must be completed within 35 minutes.
핵심 특징
- 도장 및 비도장 림용 반광 마감
- 최대 +1050C 내열성
- 특수 수지에 의한 브레이크 오일 저항성
- 박리 없는 최대 8um 유연 피막
- 일반 세정제로 제거 불가
- 오래 지속되는 오염 방지 피막
- 적은 제품 사용량
사용법
- Surface Cleaner Ultima로 표면을 세정한 후 Surface Cleaner Neutra로 중화합니다.
- 어플리케이터 블록에 도포용 천을 올려 놓습니다.
- 천에 제품을 12~18방울 떨어뜨린 뒤, 최대 50×50cm 구획으로 나눠 눈에 보이는 피막이 생길 때까지 빠르게 펴 바릅니다.
- 습도와 온도에 따라 약 1~3분간 건조시킵니다.
- Special Coating Towel로 가장자리부터 중앙 방향으로 직선 동작을 이용해 잉여 제품을 제거합니다.
- 새로운 Special Coating Towel로 가장자리부터 중앙 방향으로 원형 동작을 이용해 가볍게 버핑합니다.
- 얼룩이 남아 있으면 새 타월로 반복하고, 광원으로 확인하면서 작업합니다.
- 재코팅은 20분 후 가능하며, 35분 이내에 완료해야 합니다.