Jeweling Polish
쥬얼링 폴리시
Jeweling Polish is an ultra-fine water-based finishing polish formulated for the final stage of the polishing process, delivering a flawless, deep-gloss result ideal for show car presentation. Its filler-free formula removes residual haze, holograms and marring while enhancing color depth and reflectivity — particularly on dark and metallic finishes. The low-oil content allows for easy removal and leaves the surface ready for sealant, wax or coating application.
쥬얼링 폴리시는 폴리싱 과정의 마지막 단계를 위해 설계된 초미세 수성 마무리 폴리시로, 쇼카 수준의 완벽하고 깊이 있는 광택을 구현합니다. 필러가 없는 성분으로 잔여 뿌연 자국, 홀로그램 및 미세 스크래치를 제거하면서 특히 어두운 색상과 메탈릭 도장에서 색 깊이와 반사율을 높입니다. 저유분 함량으로 잔여물 없이 손쉽게 닦아내며 실란트, 왁스 또는 코팅 도포 전 완벽한 베이스를 만들어 줍니다.
- Brand
- PAICAR
- Categories
- Exterior : Polishes
Key features
- Ultra-fine water-based finishing polish for final polishing stage
- Removes haze, holograms and residual marring
- Enhances color depth and reflectivity on dark and metallic paints
- Completely filler-free for a true, transparent result
- Low oil content for easy, streak-free removal
- Leaves surface ready for sealant, wax or coating
- Cut level 3/10, Finish level 10/10
Usage
- Ensure the surface is already corrected and free of visible defects; remove any residue from the previous polish with a clean microfiber towel and IPA solution, then verify the panel is cool and dry.
- Select an ultra-soft or finishing foam pad and use a dual action polisher with a maximum 8 mm orbit.
- Shake the bottle well, apply 2–3 drops onto the pad, and spread the polish over the panel with the machine off to avoid splatter.
- Start at low speed to distribute the product, then slightly increase speed to activate polishing; work cross-hatch passes in approximately 40×40 cm sections with minimal pressure.
- After 2–4 passes, stop and remove residue with a clean dry microfiber towel; inspect with an inspection light to confirm optimal gloss and cleanliness.
- Once the desired finish is achieved, clean the surface with an IPA solution and apply the chosen sealant, wax or coating.
핵심 특징
- 최종 버핑 단계를 위한 초미세 수성 마무리 폴리시
- 뿌연 자국, 홀로그램 및 잔여 미세 스크래치 제거
- 어두운 색상과 메탈릭 도장의 색 깊이와 반사율 향상
- 정확한 검사 결과를 위한 완전 무필러 성분
- 얼룩 없는 손쉬운 제거를 위한 저유분 함량
- 실란트, 왁스 또는 코팅 도포에 적합한 표면 준비
- 연마성 3/10, 광택도 10/10
사용법
- 표면이 이미 교정되고 육안으로 보이는 결함이 없는지 확인한 후, 깨끗한 마이크로파이버 타올과 IPA 용액으로 이전 폴리시 잔여물을 제거하고 패널이 차갑고 건조한지 확인합니다.
- 초소프트 또는 마무리용 폼 패드를 선택하고 최대 8mm 오빗의 듀얼 액션 연마기를 사용합니다.
- 병을 충분히 흔들고 패드에 2~3방울을 도포한 후, 튀지 않도록 기계를 끈 상태에서 패널 전체에 폴리시를 고르게 펴줍니다.
- 저속으로 시작하여 제품을 분산시킨 후 속도를 약간 높여 광택 작업을 활성화하고, 약 40×40cm 구역에서 최소한의 압력으로 교차 방향 패스를 진행합니다.
- 2~4회 패스 후 작업을 멈추고 깨끗하고 건조한 마이크로파이버 타올로 잔여물을 제거한 다음, 검사등으로 최적의 광택과 청결도를 확인합니다.
- 원하는 마감이 완성되면 IPA 용액으로 표면을 닦고 선택한 실란트, 왁스 또는 코팅을 도포합니다.