PAICAR 02 Fast Cut Dilution Ratios & User Guide

PAICAR 02 Fast Cut dilution ratio and pH specification chart

02 패스트 컷

PAICAR 02 Fast Cut — Exterior : Polishes. See full specs and usage on the Find Your Detail product page: https://findyourdetail.io/products/paicar/02-fast-cut

PAICAR 02 패스트 컷 — Exterior : Polishes. 전체 사양·사용법은 Find Your Detail 제품 페이지에서 확인하세요: https://findyourdetail.io/products/paicar/02-fast-cut

02 Fast Cut is a medium-cut water-based compound that clears medium-depth defects, haze and everyday imperfections, including P2000 to P3000 sanding marks. With no silicones or fillers, it leaves a clean, even, haze-free finish and works smoothly without generating dust. Use it as an intermediate step after a stronger compound or as a single step on paint in good condition.

02 패스트 컷은 중간 깊이의 결함, 헤이즈, 일상적인 흠집과 P2000~P3000 샌딩 자국을 정리하는 중간 연마성 수성 컴파운드입니다. 실리콘과 필러가 없어 먼지 없이 깔끔하고 고른 헤이즈 없는 마감을 남깁니다. 더 강한 컴파운드 다음 중간 단계로 쓰거나 상태가 좋은 도장에 원스텝으로 사용할 수 있습니다.

Brand
PAICAR
Categories
Exterior : Polishes
Primary dilution
RTU
Where to buy
Amazon (US) — As an Amazon Associate, Find Your Detail earns from qualifying purchases.
Last updated
2026-06-02

Key features

Dilution

UseDilutionRatio
Exterior : Polishes (primary)RTU1:0

Usage

  1. Wash and fully decontaminate the surface, using a clay bar if needed, then dry the panel completely.
  2. For stronger correction pair a microfiber pad with a dual action polisher; for a better finish use a medium foam pad.
  3. Shake well, apply 3 to 4 drops to the pad, and spread over the panel with the machine off.
  4. Start at the lowest speed, then raise it to engage the abrasive, working cross-hatch passes over roughly 40 by 60 cm with light pressure and the pad flat.
  5. After 3 to 4 passes (about 2 minutes), wipe residue with a clean microfiber towel and check defect removal under an inspection light.
  6. For more gloss and depth follow with PAICAR 03, then protect the surface with a sealant or wax.

핵심 특징

  • 중간 깊이 결함과 일상 헤이즈를 위한 중간 연마성 컴파운드
  • P2000~P3000 샌딩 자국 제거
  • 중간 단계 또는 좋은 상태 도장의 원스텝으로 사용
  • 수성, 무실리콘, 무필러
  • 깔끔한 작업을 위한 무분진
  • 중간 폼 패드 또는 마이크로파이버 패드와 호환
  • 연마성 8/10, 광택도 8/10

사용법

  1. 표면을 세차하고 필요하면 클레이 바로 완전히 오염을 제거한 뒤 패널을 완전히 건조시킵니다.
  2. 강한 보정에는 듀얼 액션 폴리셔에 마이크로파이버 패드를, 더 나은 마감에는 중간 폼 패드를 사용합니다.
  3. 잘 흔든 뒤 패드에 3~4방울을 떨어뜨리고 기계를 끈 상태에서 패널에 펴 발라줍니다.
  4. 최저 속도로 시작해 속도를 올려 연마력을 살리고, 약 40×60cm 구역을 패드를 평평히 한 채 가벼운 압력으로 교차 패스합니다.
  5. 3~4회 패스(약 2분) 후 깨끗한 마이크로파이버 타올로 잔여물을 닦고 검사등으로 결함 제거를 확인합니다.
  6. 광택과 깊이를 더 원하면 PAICAR 03으로 이어 작업하고 실란트나 왁스로 표면을 보호합니다.

Also known as: PAI, 파이카, 파이, PAICAR 02 Fast Cut, FC2, PAICAR FC2, 파이카 02 패스트 컷, 파이카 FC2

한국어로 보기

Sources

Related products

More from PAICAR

More Polishes products

Explore more