01 Heavy Cut
01 헤비 컷
01 Heavy Cut is a balanced water-based compound formulated for effective and versatile paint correction, targeting heavy swirl marks, moderate scratches and visible defects including sanding marks between P1500 and P2000. Its controlled workability allows progressive defect removal with minimal secondary defects, and it is compatible with both rotary polishers for more aggressive correction and dual action polishers for a refined finish. The product wipes off easily, keeping working time efficient.
01 헤비 컷은 P1500~P2000 연마 자국을 포함하여 심한 미세 스크래치, 중간 스크래치 및 눈에 띄는 결함에 대한 효과적이고 다목적 도장 교정을 위해 설계된 균형 잡힌 수성 컴파운드입니다. 부가적인 결함을 최소화하면서 점진적으로 결함을 제거하는 제어된 작업성을 제공하며, 공격적인 교정을 위한 로터리 연마기와 정밀한 마감을 위한 듀얼 액션 연마기 모두와 호환됩니다. 잔여물이 쉽게 닦여 작업 시간을 효율적으로 유지합니다.
- Brand
- PAICAR
- Categories
- Exterior : Polishes
Key features
- Effective correction of heavy swirl marks, moderate scratches and visible defects
- Removes sanding marks between P1500 and P2000
- Compatible with rotary and dual action polishers
- Balanced water-based formula for smooth, controlled workability
- Progressive defect removal with minimal secondary defects
- Easy product removal to reduce working time
- Cut level 9/10, Finish level 6/10
Usage
- Ensure the surface is clean and fully decontaminated (wash thoroughly, use clay bar if necessary), then dry the panel completely before starting.
- For more aggressive correction use a microfiber pad with a rotary polisher; for a superior finish use a medium foam pad with a dual action polisher.
- Shake the bottle well, apply 3–4 drops onto the pad, and spread the compound over the panel with the machine off, lightly dabbing it on.
- Begin at the lowest speed to distribute the product, then gradually increase speed to activate the abrasive action; work cross-hatch passes in approximately 40×40 cm areas, applying light pressure with the pad flat on the surface.
- After 3–4 passes (approximately 2 minutes), stop and remove residue with a clean soft microfiber towel; inspect with an inspection light to verify defect removal.
- If needed, follow up with a finishing polish to increase gloss and depth, then protect the surface with a sealant or wax.
핵심 특징
- 심한 미세 스크래치, 중간 스크래치 및 눈에 띄는 결함 효과적 교정
- P1500~P2000 연마 자국 제거
- 로터리 및 듀얼 액션 연마기와 호환
- 부드럽고 제어된 작업성을 위한 균형 잡힌 수성 성분
- 부가 결함을 최소화한 점진적 결함 제거
- 작업 시간 단축을 위한 손쉬운 잔여물 제거
- 연마성 9/10, 광택도 6/10
사용법
- 표면이 깨끗하고 완전히 오염이 제거되었는지 확인(충분한 세차, 필요 시 클레이 바 사용)하고 작업 전 패널을 완전히 건조시킵니다.
- 더 공격적인 교정이 필요하면 로터리 연마기에 마이크로파이버 패드를, 더 나은 마감을 원하면 듀얼 액션 연마기에 중간 폼 패드를 사용합니다.
- 병을 충분히 흔들고 패드에 3~4방울을 도포한 후, 기계를 끈 상태에서 컴파운드를 패널에 가볍게 두드리며 고르게 펴줍니다.
- 최저 속도로 시작하여 제품을 분산시킨 후 서서히 속도를 높여 연마 작용을 활성화하고, 약 40×40cm 구역에서 패드를 표면에 평평하게 유지하며 가볍게 교차 방향 패스를 진행합니다.
- 3~4회 패스(약 2분) 후 작업을 멈추고 깨끗하고 부드러운 마이크로파이버 타올로 잔여물을 제거한 다음, 검사등으로 결함 제거 여부를 확인합니다.
- 필요하다면 마무리 폴리시로 후속 작업하여 광택과 깊이를 높인 후 실란트 또는 왁스로 표면을 보호합니다.