Nanolex Si3D Cerabide HD
나놀렉스 Si3D 세라바이드 HD
Nanolex Si3D Cerabide HD is a next-generation ceramic coating that fuses the technologies of Si3D HD and Si3D Cerabide for unsurpassed protection. The unique blend of PHPS and organopolysilazane with coated nano-sized SiO2 particles fills small existing scratches in paint while delivering superior hydrophobicity. Designed for clear-coated paint, rims (clear coated and uncoated) and hard plastics, it offers up to 100,000 km or 100 washes of durability.
나놀렉스 Si3D 세라바이드 HD는 Si3D HD와 Si3D 세라바이드의 기술을 융합하여 최고 수준의 보호력을 제공하는 차세대 세라믹 코팅입니다. PHPS와 오가노폴리실라잔에 코팅된 나노 사이즈 SiO2 입자가 결합된 독특한 조성은 도장의 미세 스크래치를 채우면서도 우수한 발수성을 발휘합니다. 클리어코트 도장, 휠(클리어코트 및 무도장), 단단한 플라스틱에 적합하며 최대 100,000 km 또는 100회 세차까지 내구성을 발휘합니다.
- Brand
- Nanolex
- Categories
- Exterior : Coating
Key features
- Dual protection: combines strengths of Si3D HD and Si3D Cerabide for unparalleled protection against environmental influences and contamination
- Restorative effect: nano-sized SiO2 particles fill and smooth existing scratches, renewing the paint surface
- Superior hydrophobicity: advanced water-repellent properties for effortless cleaning and maintenance
- Unrivaled longevity: durability up to 100,000 km or 100 washes
- Unique composition of PHPS and organopolysilazane with solid, coated nano-sized SiO2 particles
- Suitable for clear coated surfaces, rims (clear coated and uncoated) and hard plastics
Usage
- Safety: Wear appropriate personal protective equipment when handling and applying. Refer to the label for further information.
- Optimal conditions: Temperature 5–30°C, humidity 30–70%. Choose a shady spot away from direct sunlight.
- Cleaning: Use on clear coated surfaces, rims (clear coated and uncoated) and hard plastics. Surfaces must be thoroughly dried and completely free of contaminants, dust and other residues.
- After machine polishing, wash with Nanolex PreWash Concentrate, then use Nanolex EX immediately before applying Si3D Cerabide HD to remove fillers and surface residues. Turn or replace the microfiber cloth as needed.
- Application: Apply 8–10 drops of Nanolex Si3D Cerabide HD to a clean applicator cloth.
- Spread the product evenly over the surface in crisscross motions, covering all areas without excessive pressure, until no visible traces of wetness remain.
- Wait 2–3 minutes, then gently rub away the residue with a soft microfiber cloth using gentle movements without pressure.
- Drying/curing: Allow to cure at room temperature for at least 24 hours in a well-ventilated, non-air-conditioned area; no water contact during this time.
- Do not wash the vehicle or treated surfaces for the first 7 days after application.
핵심 특징
- 이중 보호: Si3D HD와 Si3D 세라바이드의 장점을 결합하여 환경 영향과 오염에 대한 비할 데 없는 보호 제공
- 회복 효과: 나노 사이즈 SiO2 입자가 기존 스크래치를 채우고 매끄럽게 하여 도장 표면을 새롭게 함
- 탁월한 발수성: 손쉬운 세척과 관리를 위한 최첨단 발수 기능
- 최고의 내구성: 최대 100,000 km 또는 100회 세차 내구성
- PHPS와 오가노폴리실라잔, 코팅된 고체 나노 SiO2 입자의 독특한 조성
- 클리어코트 도장, 휠(클리어코트 및 무도장), 단단한 플라스틱에 적합
사용법
- 안전: 취급 및 도포 시 적절한 개인 보호 장비를 착용하고, 자세한 내용은 라벨을 참조합니다.
- 최적 조건: 온도 5–30°C, 습도 30–70%. 직사광선이 없는 그늘진 곳에서 작업합니다.
- 세척: 클리어코트 도장, 휠(클리어코트 및 무도장), 단단한 플라스틱에 사용합니다. 표면은 완전히 건조되고 오염물·먼지·잔여물이 없어야 합니다.
- 머신 폴리싱 후에는 나놀렉스 프리워시 컨센트레이트로 세차하고, Si3D 세라바이드 HD 도포 직전 나놀렉스 EX를 사용하여 필러와 표면 잔여물을 제거합니다. 필요 시 마이크로파이버 천을 뒤집거나 교체합니다.
- 도포: 깨끗한 도포용 천에 8–10방울의 Si3D 세라바이드 HD를 떨어뜨립니다.
- 과도한 압력을 가하지 않고 교차 동작으로 모든 부위를 고르게 펴 바르며, 젖은 흔적이 보이지 않을 때까지 작업합니다.
- 2–3분 기다린 후 부드러운 마이크로파이버 천으로 압력 없이 부드러운 동작으로 잔여물을 닦아냅니다.
- 건조/경화: 통풍이 잘 되고 에어컨이 작동하지 않는 곳에서 최소 24시간 실온에서 경화시키며, 이 기간 동안 물에 닿지 않도록 합니다.
- 도포 후 첫 7일 동안 차량이나 처리된 표면을 세차하지 않습니다.