Bilt Hamber Dynax-UC
빌트 햄버 다이낙스-UC (하부 투명 방청 왁스)
Dynax-UC is an anti-corrosion wax that builds a low-thickness, near-transparent protective film for underbodies and exposed metalwork. The firm wax-like film carries metal-seeking corrosion inhibitors that help arrest existing corrosion and slow new corrosion, making it useful where dark waxes or underseal would spoil the look of bodywork.
다이낙스-UC는 차량 하부와 노출된 금속 면에 얇고 거의 투명한 보호 피막을 형성하는 방청 왁스입니다. 단단한 왁스형 피막에는 금속을 찾아가는 부식 억제제가 들어 있어 기존 부식을 멈추고 새로운 부식을 늦추는 데 도움을 주며, 어두운 왁스나 언더실이 도장면 외관을 해칠 수 있는 부위에 적합합니다.
- Brand
- Bilt Hamber
- Categories
- Exterior : Coating
Key features
- Near-transparent film at about 50 microns DFT
- Firm wax-like film resists dirt pick-up
- Metal-seeking corrosion inhibitors
- Safe on bare metal or painted surfaces
- Aerosol works on its side and upside down
- Coverage about 8-10 sq m per litre
- Cures fully in about 24-96 hours, vehicle usable after about 30 minutes
Usage
- Clean and dry the underbody and wheel arches thoroughly, removing all loose rust, dirt and grease.
- Mask off brake components, exhaust, rubber bushes and drive shafts.
- Shake the aerosol for at least about 2 minutes before and during use.
- Spray evenly from about 25-30cm onto exposed chassis, suspension arms and wheel-arch liners; Dynax-UC is harder-wearing and more UV-stable than UB.
- Apply about 1-2 coats with about 30-60 minutes flash-off between coats.
- Allow about 24 hours to cure fully so the tough, slightly flexible film can resist stone chipping and road salt.
- Inspect annually, especially leading edges and high-impact zones, and touch up as needed.
핵심 특징
- 약 50마이크론 건조 도막에서 거의 투명한 피막
- 단단한 왁스형 피막으로 먼지 부착이 적음
- 금속을 찾아가는 부식 억제제 함유
- 베어메탈과 도장면 모두에 안전
- 에어로졸이 옆이나 거꾸로도 분사 가능
- 1리터당 약 8~10m² 도포
- 약 24~96시간 내 완전 경화, 약 30분 후 차량 사용 가능
사용법
- 언더바디와 휠하우스를 철저히 세척하고 건조시키며, 녹·먼지·유분을 모두 제거합니다.
- 브레이크 부품·배기계·고무 부싱·드라이브 샤프트 등을 마스킹합니다.
- 사용 전과 사용 중에도 에어로졸을 최소 약 2분간 흔들어 줍니다.
- 약 25~30cm 거리에서 노출 섀시·서스펜션 암·휠하우스 라이너에 균일하게 분사합니다. 다이낙스-UC는 UB보다 내마모성과 UV 안정성이 더 좋습니다.
- 약 1~2회 도포하며, 코트 간 약 30~60분의 플래시 오프 시간을 둡니다.
- 약 24시간 동안 완전 경화시켜, 단단하면서도 약간 유연한 피막이 돌빵과 염해에 잘 견디게 합니다.
- 특히 선단부와 충격이 큰 부위를 매년 점검하고 필요하면 보수 도포합니다.