나노렉스 Si3D 세라바이드 HD
Nanolex Si3D Cerabide HD
나노렉스 · Si3D Cerabide HD · Si3D CERABIDE HD · Nanolex Cerabide HD · Cerabide HD · Si3D HD Cerabide · 나노렉스 세라바이드 HD · Si3D 세라바이드 HD · 세라바이드 HD · 세라믹 코팅 HD · Si3D Cerabide HD Coating · Si3D CERABIDE HD Ceramic Coating
Si3D HD와 Si3D 세라바이드의 기술을 결합해 만든 차세대 세라믹 코팅입니다. PHPS와 오가노폴리실라잔 베이스에 코팅된 나노 SiO2 입자가 어우러져 도장의 아주 미세한 스크래치를 채우는 데 도움을 주면서, 강한 발수성을 가진 보호 막을 형성합니다. 클리어코트 도장, 휠(클리어코트 및 무도장), 단단한 플라스틱에 사용할 수 있으며 내구성은 약 100,000km 또는 100회 세차 수준으로 안내됩니다.
- 브랜드
- Nanolex
- 카테고리
- Exterior : Coating
- 기본 희석 비율
- RTU
핵심 특징
- Si3D HD와 Si3D 세라바이드 기술의 결합
- 나노 SiO2 입자가 미세 스크래치 채움에 도움
- 강한 발수성을 가진 보호 막
- 약 100,000km 또는 100회 세차 수준의 내구성
- PHPS, 오가노폴리실라잔, 코팅된 SiO2 입자 기반 조성
- 클리어코트 도장, 휠, 단단한 플라스틱에 사용
희석 비율
- Exterior : Coating — RTU (1:0) (기본)
사용법
- 적절한 개인 보호 장비를 착용하고 라벨의 안내를 따릅니다.
- 온도 5~30°C, 습도 30~70%, 직사광선이 없는 그늘진 환경에서 작업합니다.
- 건조하고 오염이 없는 클리어코트 도장, 휠(클리어코트 및 무도장), 단단한 플라스틱에만 사용합니다.
- 머신 폴리싱 후에는 Nanolex PreWash Concentrate로 세차하고, 도포 직전 Nanolex EX로 마무리 탈지하며, 필요하면 천을 뒤집거나 교체합니다.
- 깨끗한 어플리케이터 천에 Si3D 세라바이드 HD 8~10방울을 떨어뜨립니다.
- 과도한 압력 없이 크로스 동작으로 패널 전체에 고르게 펴 바르며, 젖은 흔적이 보이지 않을 때까지 작업합니다.
- 2~3분 기다린 뒤 부드러운 마이크로파이버 타월로 압력 없이 잔여물을 닦아냅니다.
- 통풍이 잘되고 에어컨이 작동하지 않는 곳에서 상온으로 최소 24시간 경화시키며, 이 기간 동안 물에 닿지 않도록 합니다.
- 도포 후 첫 7일 동안은 차량이나 처리된 표면을 세차하지 않습니다.
A next-generation ceramic coating that combines the technologies behind Si3D HD and Si3D Cerabide. The blend of PHPS and organopolysilazane with coated nano-sized SiO2 particles helps fill very fine scratches in paint while building a strongly hydrophobic protective layer. Designed for clear-coated paint, rims (clear coated and uncoated) and hard plastics, with a quoted durability of up to roughly 100,000 km or 100 washes.
Key features
- Combines the technologies of Si3D HD and Si3D Cerabide
- Nano-sized SiO2 particles help fill fine scratches
- Strong hydrophobic protective layer
- Durability around 100,000 km or 100 washes
- Composition of PHPS, organopolysilazane and coated SiO2 particles
- Use on clear-coated paint, rims and hard plastics
Usage
- Wear appropriate personal protective equipment and follow the label instructions.
- Work between 5 and 30°C with 30 to 70% humidity, in a shaded area away from direct sunlight.
- Use only on clear-coated paint, rims (clear coated and uncoated) and hard plastics that are dry and free of contamination.
- After machine polishing, wash with Nanolex PreWash Concentrate and wipe down with Nanolex EX immediately before coating; turn or replace the cloth as needed.
- Place 8 to 10 drops of Si3D Cerabide HD onto a clean applicator cloth.
- Spread evenly in crisscross motions across the panel without excessive pressure until no wet streaks remain.
- Wait 2 to 3 minutes, then gently wipe off the residue with a soft microfiber cloth using no pressure.
- Cure at room temperature for at least 24 hours in a well-ventilated, non-air-conditioned area with no water contact.
- Do not wash the vehicle or treated surfaces for the first 7 days after application.