EXO and Crystal Serum Light
엑소 앤 크리스탈 세럼 라이트
This kit combines Crystal Serum Light with EXOv5 to deliver paint protection that pairs CSL chemical and scratch resistance with the strong hydrophobic behavior of EXOv5. CSL also performs as a standalone ceramic coating for gloss retention; layered with EXOv5, the surface gains a high-gloss finish that repels water, bird droppings, and contaminants.
이 키트는 크리스탈 세럼 라이트(CSL)와 EXOv5를 결합해 CSL의 화학·스크래치 저항성에 EXOv5의 강한 발수 성능을 더한 도장 보호 솔루션을 제공합니다. CSL 자체로도 우수한 단독 세라믹 코팅이며, EXOv5를 적층하면 물과 새 배설물, 오염을 잘 밀어내는 고광택 마감이 완성됩니다.
- Brand
- GTECHNIQ
- Categories
- Exterior : Coating
Key features
- Chemical resistance from a prosumer-grade product
- High gloss
- CSL up to about 5 years of durability
- EXOv5 improved durability
- EXOv5 high gloss plus water and dirt repellency
- EXOv5 easier application
Usage
- Apply CSL indoors and keep the vehicle indoors for 12 hours afterwards, out of direct sunlight.
- Apply only between 5 and 25 degrees Celsius.
- Shake well and wear gloves.
- Wash and decontaminate the paint, polishing first if needed to remove imperfections.
- Spray Panel Wipe onto an MF1 cloth and wipe each panel in small sections.
- Soak the application pad with three pipette measures of CSL and work it in evenly.
- Cap the bottle and set it aside to avoid premature curing.
- Apply CSL in overlapping strokes across roughly 2ft by 2ft or along body lines.
- Remove residue immediately with an MF1 cloth, rotating two cloths and avoiding heavy pressure.
- Inspect the panel under bright, diffused light for any remaining residue.
- Wait about 2 hours after CSL before applying EXOv5 or C2.
- For EXOv5, prime the AP2 applicator until damp, apply in overlapping strokes per panel half, remove residue with an MF1, and follow with a second MF1 to clear smearing.
핵심 특징
- 프로슈머 등급의 화학 저항성
- 고광택 마감
- CSL 최대 약 5년 내구성
- EXOv5: 향상된 내구성
- EXOv5: 우수한 광택과 발수·방오 성능
- EXOv5: 쉬워진 시공성
사용법
- CSL는 실내에서 시공하고, 시공 후 12시간은 차량을 실내에 두며 직사광선을 피합니다.
- 5°C ~ 25°C 사이 온도에서만 시공합니다.
- 잘 흔들고 장갑을 착용합니다.
- 도장면을 철저히 세차·제염하고 필요 시 폴리싱으로 결함을 제거합니다.
- Panel Wipe를 MF1 천에 분무해 패널을 작은 부분씩 닦아냅니다.
- 피펫으로 CSL을 3정량씩 어플리케이션 패드에 적셔 고르게 스미게 합니다.
- 뚜껑을 닫아 한쪽에 두어 조기 경화를 방지합니다.
- 약 2ft x 2ft 면적 또는 차체 라인을 따라 CSL을 겹쳐 도포합니다.
- MF1 천 두 장을 번갈아 사용해 즉시 잔여물을 제거하며 강한 힘은 피합니다.
- 밝고 분산된 조명으로 잔여물 유무를 확인합니다.
- CSL 시공 후 약 2시간 기다린 뒤 EXOv5 또는 C2를 도포합니다.
- EXOv5는 AP2 어플리케이터에 패드가 촉촉할 정도로 적셔 패널 절반씩 겹쳐 도포한 뒤 MF1 천으로 즉시 잔여물을 제거하고, 두 번째 MF1으로 얼룩을 마무리합니다.