Wheel Coating
휠 코팅
Armour Wheel Quartz Coating is a high-performance ceramic coating built for wheels, with 76 percent SiO2 solids and a formula that holds up to heat and heavy use. It forms a long-lasting barrier that repels brake dust and contaminants, making routine wheel cleaning easier. Safe on anodized, chrome, painted, powder-coated, clear-coated aluminum, and matte finishes, with rated durability of more than 15,000 miles or 1+ year.
Armour 휠 쿼츠 코팅은 휠 보호와 외관 유지를 위해 만든 고성능 세라믹 코팅으로, 76% SiO2 솔리드 함량과 열·가혹한 사용에 견디는 포뮬러를 갖췄습니다. 브레이크 더스트와 오염물을 강하게 반발하는 지속적인 보호막을 형성해 평소 휠 세척을 쉽게 만들어 줍니다. 아노다이즈드·크롬·페인트·파우더 코트·클리어 코트 알루미늄·매트 마감에 안전하며, 15,000마일 또는 1년 이상의 내구성을 제공합니다.
- Brand
- Armour Detail Supply
- Categories
- Exterior : Coating, Exterior : Tire&Wheel Sealant
Key features
- 76 percent SiO2 solids
- Heat and abuse resistant formula
- Repels brake dust and contaminants
- Compatible with anodized, chrome, painted, powder-coated, clear-coated aluminum, matte finishes
- Durability of 15,000+ miles or 1+ year
- Easier wheel maintenance
- Includes 30 ml coating, mini microfiber applicator pad, instruction card
Usage
- Decontaminate the wheel surface with Armour Wheel Cleaner, then lift any embedded contamination with a clay bar or synthetic clay mitt.
- If swirls or scratches are visible, polish the surface to reduce defects and bring up gloss.
- Wipe with Armour Panel Prep to clear oils and residue, repeating twice when polishing was skipped.
- Prime the applicator with three lines of coating; later wheels only need a small amount.
- Apply one wheel at a time in back-and-forth or crosshatch motions and let the coating set up 1-3 minutes (about 1-2 minutes typically) until light hazing appears.
- Level 95 percent or more on the first wipe with a short-nap pearl-weave towel; lengthen set-up if it smears, shorten if removal is hard.
- Switch to a plush towel for final leveling and check for streaks or cloudy/dark high spots, repeating per wheel and using a fresh towel side every wheel.
- Two layers are recommended for maximum durability, with 1-2 hours between coats.
- Allow at least 12 hours of initial cure before driving and water exposure, and avoid washes or chemicals for 7 days; AMPLIFY or Ceramic Spray Sealant can be added 4 hours after application.
핵심 특징
- 76% SiO2 솔리드 함량
- 열·가혹한 사용에 강한 포뮬러
- 브레이크 더스트·오염물 반발
- 아노다이즈드·크롬·페인트·파우더 코트·클리어 코트 알루미늄·매트 마감과 호환
- 15,000마일 또는 1년 이상 내구성
- 휠 유지관리 용이
- 30ml 코팅, 미니 마이크로파이버 어플리케이터 패드, 사용 설명 카드 포함
사용법
- Armour 휠 클리너로 휠 표면을 디컨한 뒤 클레이바 또는 합성 클레이 미트로 박힌 오염을 제거합니다.
- 스월이나 스크래치가 있다면 폴리싱으로 결함을 줄이고 광택을 끌어올립니다.
- Armour 패널 프렙으로 오일과 잔여물을 제거하고, 폴리싱을 하지 않았다면 두 번 반복합니다.
- 어플리케이터를 3줄 도포로 프라이밍하고 이후 휠에는 소량만 추가합니다.
- 한 번에 한 휠씩 백앤포스 또는 크로스해치 모션으로 도포한 뒤 1-3분(보통 1-2분) 셋업해 가벼운 헤이즈가 나타날 때까지 기다립니다.
- 숏냅 펄 위브 타월로 1차 와이프에서 95% 이상 레벨링합니다. 번지면 셋업 시간을 늘리고, 제거가 어려우면 줄입니다.
- 플러시 타월로 최종 레벨링하고 흐리거나 어두운 하이스팟·스트릭을 확인하며 휠마다 새 면을 사용합니다.
- 최대 내구성을 위해 2레이어를 권장하며 레이어 사이에 1-2시간 간격을 둡니다.
- 최소 12시간 초기 경화 후 주행과 물 노출이 가능하며, 7일간 세차나 케미컬 노출은 피합니다. 도포 4시간 후 AMPLIFY나 세라믹 스프레이 실런트를 추가로 올릴 수 있습니다.