Coating Primer
코팅 프라이머
A nano-particle base-layer coating primer designed to be applied beneath hard ceramic or glass coatings to strengthen the paint's fundamental resistance. It helps protect low-density or delicate paint from deep staining and surface depression, doubling the effective protection period compared to using a hard coating alone. Must be applied indoors in a controlled humidity environment with sufficient curing time.
경화계 코팅제 아래에 적용하는 나노 입자 베이스층 코팅 프라이머입니다. 도장의 근본적인 내구성과 오염 방지력을 강화하며, 저밀도·민감한 도장의 심한 물자국이나 도장 함몰로부터 보호하는 기간을 경화계 코팅 단독 대비 약 2배까지 연장합니다. 반드시 실내(차고)에서 충분한 건조 시간을 확보하고 시공해야 합니다.
- Brand
- Ganbass
- Categories
- Exterior : Coating
- Primary dilution
- RTU
Key features
- Nano-particle base primer for hard coating systems
- Strengthens paint durability and contamination resistance
- Extends protection period for low-density paint
- Adjustable coating hardness based on number of coats applied
- High component retention in a single application pass
- Must be applied indoors (garage) with controlled humidity
- Curing time: 28–192 hours depending on coat count and humidity
Dilution
- Exterior : Coating — RTU (1:0) (primary)
Usage
- After washing, perform any necessary paint correction and decontamination; use REBOOT as a mandatory step to reset the paint surface.
- Apply the primer to a detail cloth and spread it across one panel at a time, then immediately wipe off the excess with a separate dry cloth.
- Check for streaks or uneven application using a handheld light from multiple angles, paying close attention to edges and recessed areas.
- For the recommended two-coat application, allow at least 2 hours between coats; allow at least 2 hours between the second and third coat if a third is applied.
- Cure in a garage at 20–80% humidity: approximately 28–96 hours for one coat, 96–144 hours for two coats, 144–192 hours for three coats.
- Once fully cured, apply a hard ceramic or glass coating (such as BETA or AVELL) over the primer as a top layer.
핵심 특징
- 경화계 코팅 시스템용 나노 입자 베이스 프라이머
- 도장 내구성 및 오염 방지력 강화
- 저밀도 도장의 보호 기간 연장
- 도포 횟수에 따라 코팅 경도 조절 가능
- 1회 도포로 높은 성분 잔류율
- 반드시 실내(차고)에서 습도 관리하며 시공
- 경화 시간: 도막 횟수·습도에 따라 28~192시간
사용법
- 세차 후 필요한 연마 및 하지 처리를 진행하고, REBOOT로 도장을 리셋하는 작업을 반드시 수행합니다.
- 디테일 클로스에 프라이머를 묻혀 패널별로 도포한 후, 즉시 다른 마른 클로스로 잉여분을 닦아냅니다.
- 핸디 라이트를 여러 각도로 비춰 얼룩이나 도포 불균일이 없는지 확인하고, 에지 및 오목한 부위를 특히 주의합니다.
- 권장 2회 도포 시 1회와 2회 사이에 최소 2시간 이상 간격을 두며, 3회 도포 시도 동일하게 간격을 유지합니다.
- 차고 내 습도 20~80% 환경에서 경화시킵니다: 1회 도포 약 28~96시간, 2회 도포 약 96~144시간, 3회 도포 약 144~192시간.
- 완전 경화 후 BETA, AVELL 등 경화계 코팅제를 상도로 중첩 시공합니다.
Also known as: 간바스, ganbas, Ganbass Coating Primer, 간바스 코팅 프라이머