코팅 프라이머
Coating Primer
경화계 코팅제 아래에 적용하는 나노 입자 베이스층 코팅 프라이머입니다. 도장의 근본적인 내구성과 오염 방지력을 강화하며, 저밀도·민감한 도장의 심한 물자국이나 도장 함몰로부터 보호하는 기간을 경화계 코팅 단독 대비 약 2배까지 연장합니다. 반드시 실내(차고)에서 충분한 건조 시간을 확보하고 시공해야 합니다.
- 브랜드
- Ganbass
- 카테고리
- Exterior : Coating
- 기본 희석 비율
- RTU
핵심 특징
- 경화계 코팅 시스템용 나노 입자 베이스 프라이머
- 도장 내구성 및 오염 방지력 강화
- 저밀도 도장의 보호 기간 연장
- 도포 횟수에 따라 코팅 경도 조절 가능
- 1회 도포로 높은 성분 잔류율
- 반드시 실내(차고)에서 습도 관리하며 시공
- 경화 시간: 도막 횟수·습도에 따라 28~192시간
희석 비율
- Exterior : Coating — RTU (1:0) (기본)
사용법
- 세차 후 필요한 연마 및 하지 처리를 진행하고, REBOOT로 도장을 리셋하는 작업을 반드시 수행합니다.
- 디테일 클로스에 프라이머를 묻혀 패널별로 도포한 후, 즉시 다른 마른 클로스로 잉여분을 닦아냅니다.
- 핸디 라이트를 여러 각도로 비춰 얼룩이나 도포 불균일이 없는지 확인하고, 에지 및 오목한 부위를 특히 주의합니다.
- 권장 2회 도포 시 1회와 2회 사이에 최소 2시간 이상 간격을 두며, 3회 도포 시도 동일하게 간격을 유지합니다.
- 차고 내 습도 20~80% 환경에서 경화시킵니다: 1회 도포 약 28~96시간, 2회 도포 약 96~144시간, 3회 도포 약 144~192시간.
- 완전 경화 후 BETA, AVELL 등 경화계 코팅제를 상도로 중첩 시공합니다.
A nano-particle base-layer coating primer designed to be applied beneath hard ceramic or glass coatings to strengthen the paint's fundamental resistance. It helps protect low-density or delicate paint from deep staining and surface depression, doubling the effective protection period compared to using a hard coating alone. Must be applied indoors in a controlled humidity environment with sufficient curing time.
Key features
- Nano-particle base primer for hard coating systems
- Strengthens paint durability and contamination resistance
- Extends protection period for low-density paint
- Adjustable coating hardness based on number of coats applied
- High component retention in a single application pass
- Must be applied indoors (garage) with controlled humidity
- Curing time: 28–192 hours depending on coat count and humidity
Usage
- After washing, perform any necessary paint correction and decontamination; use REBOOT as a mandatory step to reset the paint surface.
- Apply the primer to a detail cloth and spread it across one panel at a time, then immediately wipe off the excess with a separate dry cloth.
- Check for streaks or uneven application using a handheld light from multiple angles, paying close attention to edges and recessed areas.
- For the recommended two-coat application, allow at least 2 hours between coats; allow at least 2 hours between the second and third coat if a third is applied.
- Cure in a garage at 20–80% humidity: approximately 28–96 hours for one coat, 96–144 hours for two coats, 144–192 hours for three coats.
- Once fully cured, apply a hard ceramic or glass coating (such as BETA or AVELL) over the primer as a top layer.
다른 이름: 간바스, ganbas, Ganbass Coating Primer, 간바스 코팅 프라이머