Heavy Cut+
헤비 컷 플러스
이우카 · EWO · 이우 · Ewocar Heavy Cut+ · HC+ · 이워카 헤비 컷 플러스
Heavy Cut+ is Ewocar's most aggressive abrasive compound, engineered for maximum cutting speed and rapid defect removal with minimal heat buildup. It outcuts the standard Heavy Cut, making it the go-to choice for severe paint imperfections that demand the fastest correction. Designed for both rotary and dual-action polishers, it cuts aggressively without overheating the paint — safer on sensitive or heat-prone surfaces. Its water-based formula produces virtually zero dust and maintains a long working cycle even at higher machine speeds. Free of silicones and fillers.
Heavy Cut+는 Ewocar 라인업 중 가장 공격적인 연마 컴파운드로, 최소한의 열 발생으로 최대 절삭 속도와 빠른 흠집 제거를 위해 설계되었습니다. 표준 Heavy Cut보다 높은 절삭력을 발휘하여 가장 빠른 교정이 필요한 심각한 도장 결함에 최적입니다. 로터리 및 더블액션 폴리셔 모두에서 사용 가능하며, 열에 민감한 도장면에도 과열 없이 공격적인 절삭이 가능합니다. 수성 처방으로 먼지 발생이 거의 없고 고속 작업에서도 긴 작업 시간을 유지합니다. 실리콘 및 충전제 미함유.
- Brand
- EWOCAR
- Categories
- Exterior : Polishes
Key features
- Ewocar's most aggressive compound — maximum cutting power above standard Heavy Cut
- Extra-strong cutting speed for faster removal of severe defects
- Cuts aggressively without overheating the paint — safe on heat-prone surfaces
- Water-based formula with virtually zero dust and lower heat buildup
- Long working cycle maintained even at higher machine speeds
- Silicone-free and filler-free; compatible with rotary and dual-action polishers
Usage
- Ensure the paint surface is clean, dry, and free of contaminants before starting.
- Apply a moderate amount of Heavy Cut+ to a heavy-cut foam pad or wool pad suited for intensive correction.
- Set the polisher to a low speed and spread the compound evenly across the section. Heavy Cut+ can be used at higher machine speeds — keep passes controlled to avoid excess heat even though the formula is engineered to minimize heat buildup.
- Work the section in overlapping passes with firm pressure until severe defects are removed. The water-based formula stays workable through extended cycles without drying out.
- Wipe off residue with a clean microfiber cloth, then follow up with a finishing compound (e.g., Fine Cut or One Cut) to achieve the final high-gloss result.
핵심 특징
- Ewocar의 가장 공격적인 컴파운드 — 표준 Heavy Cut 대비 최대 절삭력
- 심각한 흠집의 빠른 제거를 위한 초강력 절삭 속도
- 도장면 과열 없이 공격적인 절삭 — 열에 민감한 도장면에도 안전
- 열 발생 최소화 및 먼지 거의 없는 수성 처방
- 고속 작업에서도 긴 작업 시간 유지
- 실리콘 및 충전제 미함유; 로터리 및 더블액션 폴리셔 호환
사용법
- 작업 전 도장 표면이 깨끗하고 건조하며 오염물이 없는지 확인합니다.
- 강한 교정 작업에 적합한 헤비컷 폼 패드 또는 울 패드에 Heavy Cut+를 적당량 도포합니다.
- 폴리셔를 저속으로 설정하고 작업 구간 전체에 컴파운드를 고르게 펴 바릅니다. Heavy Cut+는 고속 작업도 가능하나, 처방이 열 발생을 최소화하도록 설계되어 있어도 패스를 안정적으로 유지하여 과도한 열을 방지합니다.
- 겹치는 패스로 적절한 압력을 가하며 작업하여 심각한 흠집이 제거될 때까지 연마합니다. 수성 처방 덕분에 긴 작업 사이클에서도 건조 없이 작업성이 유지됩니다.
- 깨끗한 극세사 타월로 잔여물을 닦아낸 후, Fine Cut 또는 One Cut 등 피니싱 컴파운드로 이어서 최종 고광택 마감을 완성합니다.