Heavy Correcting Compound
헤비 커렉팅 컴파운드
Adam's Heavy Correcting Compound is a heavy-cut paint correction compound built on a water-based Diminishing Abrasive Technology blend of aluminum oxides and polishing agents. It removes heavy swirl marks, buffer halos, oxidation, stains, and roughly 1500-grit sanding marks from clear coat, single-stage, and lacquer finishes. The thin liquid lets the abrasives break down into a fine polish for a haze-free cutting step, and it is silicone-free, VOC-compliant, and body-shop safe.
아담스 헤비 커렉팅 컴파운드는 알루미늄 옥사이드와 연마제를 배합한 수성 디미니싱 어브레이시브 기술 기반의 강력 절삭 컴파운드입니다. 클리어코트, 싱글스테이지, 래커 도장면에서 심한 스월, 버퍼 자국, 산화, 얼룩과 약 1500방 샌딩 자국까지 제거합니다. 묽은 액상이 연마 과정에서 미세하게 분해되어 헤이즈 없이 마무리되며, 실리콘 무첨가에 VOC 규정을 충족하고 바디샵에서도 안전하게 사용할 수 있습니다.
- Brand
- Adam's Polishes
- Categories
- Exterior : Polishes
- Primary dilution
- RTU
Key features
- Water-based Diminishing Abrasive Technology blend of aluminum oxides and polishing agents
- Heavy cut: removes deep swirls, buffer halos, oxidation, stains and ~1500-grit sanding marks
- Thin liquid formula resists pad caking and microfiber clogging
- Low-dust with a long working time; residue wipes off cleanly
- Silicone-free, VOC-compliant, and body-shop safe
- Works on clear coat, single-stage, and lacquer finishes
Dilution
- Exterior : Polishes — RTU (1:0) (primary)
Usage
- Wash, decontaminate, and clay the vehicle before compounding.
- Apply about four drops onto a foam or microfiber cutting pad and prime the pad with a mist of detail spray.
- Spread the compound over a two-foot by two-foot section.
- Work at high speed with three to five pounds of pressure and about 25% overlap until the product turns clear.
- Wipe residue off with a clean microfiber towel and inspect the corrected surface.
핵심 특징
- 알루미늄 옥사이드와 연마제를 배합한 수성 디미니싱 어브레이시브 기술
- 강력 절삭: 깊은 스월, 버퍼 자국, 산화, 얼룩과 약 1500방 샌딩 자국 제거
- 묽은 액상으로 패드 케이킹과 마이크로파이버 막힘 방지
- 분진이 적고 작업 시간이 길며 잔여물이 깔끔하게 닦임
- 실리콘 무첨가, VOC 규정 충족, 바디샵 안전
- 클리어코트·싱글스테이지·래커 도장면에 사용 가능
사용법
- 컴파운딩 전에 세차, 철분 제거, 클레이 작업을 먼저 진행하십시오.
- 폼 또는 마이크로파이버 컷팅 패드에 약 4방울을 떨어뜨리고 디테일 스프레이를 한 번 분사해 패드를 적시십시오.
- 약 60cm × 60cm 구역에 컴파운드를 고르게 펴 바르십시오.
- 고속으로 3~5파운드 압력과 약 25% 겹침을 주며 제품이 투명해질 때까지 작업하십시오.
- 깨끗한 마이크로파이버 타월로 잔여물을 닦아내고 보정된 표면을 확인하십시오.
Also known as: ap, adams, adam's, adams-polish, 아담스, 아담스 폴리시, 아담스 폴리쉬, Adam's Heavy Correcting Compound, Adam's Polishes Heavy Correcting Compound, Adam's HCC, HCC, 아담스 헤비 커렉팅 컴파운드, 아담스 폴리시 헤비 커렉팅 컴파운드
한국어로 보기