Dynax-UB
다이낙스-UB
Dynax-UB is an underbody anti-corrosion wax that uses elastic polymers to form a tougher, more abrasion-resistant film than typical waxes for long-term protection of vehicle undersides. The touch-dry, brown wax-like film has performed strongly in ASTM B117 salt-spray testing relative to comparable products.
다이낙스-UB는 탄성 폴리머를 함유한 언더바디 방청 왁스로, 일반 왁스보다 더 단단하고 내마모성이 좋은 피막을 형성해 차량 하부를 오래 보호합니다. 터치 드라이 상태의 갈색 왁스형 피막을 만들며, 동급 제품들과 비교해 ASTM B117 염수 분무 시험에서 우수한 결과를 보입니다.
- Brand
- Bilt Hamber
- Categories
- Exterior : Coating
Key features
- Firm-film underbody anti-corrosion wax
- Elastic polymers for abrasion resistance
- Touch-dry brown wax-like film
- Strong ASTM B117 salt-spray performance
- Available as aerosol, brushable tub and spray-grade jerrycan
Usage
- Raise and safely support the vehicle, then thoroughly clean the underbody, wheel arches and chassis with a pressure washer and degreaser.
- Allow the substrate to dry fully so trapped moisture does not compromise adhesion and protection.
- Mask off exhausts, brake discs, drive shafts, rubber bushes and any area not to be coated.
- Shake the aerosol vigorously for at least about 2 minutes; for 1L cans apply via a Schutz gun at about 60-80 psi.
- Apply a uniform black coating to underbody panels, wheel arches and exposed chassis from about 20-30cm, preferring two thin coats over one heavy coat.
- Allow about 1 hour between coats and around 24 hours to reach final cure, leaving the film slightly flexible to resist stone chipping.
- Inspect annually and touch up as needed; Dynax-UC can be over-coated for additional UV and abrasion resistance if wanted.
핵심 특징
- 견고한 피막의 언더바디 방청 왁스
- 내마모성을 위한 탄성 폴리머
- 터치 드라이 갈색 왁스 피막
- ASTM B117 염수 분무 시험에서 우수한 성능
- 에어로졸·브러시 도포 용기·스프레이용 제리캔으로 제공
사용법
- 차량을 안전하게 리프팅한 뒤, 고압세척기와 탈지제로 언더바디·휠하우스·섀시를 철저히 세척합니다.
- 수분이 남아 부착과 방청 성능을 떨어뜨리지 않도록 소재를 완전히 건조시킵니다.
- 배기계·브레이크 디스크·드라이브 샤프트·고무 부싱 등 도포하지 않을 부위를 마스킹합니다.
- 에어로졸은 최소 약 2분간 강하게 흔들고, 1L 캔은 슈츠건에 약 60~80psi로 사용합니다.
- 약 20~30cm 거리에서 언더바디 패널·휠하우스·노출 섀시에 균일한 블랙 코팅을 도포하며, 두껍게 한 번보다는 얇게 두 번이 좋습니다.
- 코트 간 약 1시간, 완전 경화까지 약 24시간을 두며, 피막은 약간의 유연성을 유지해 돌빵에 잘 견딥니다.
- 매년 점검 후 필요 시 보수 도포하고, 추가적인 UV·내마모 보호를 원하면 다이낙스-UC를 오버코트할 수 있습니다.