Ethos Car Care 맥스 그래핀 코팅 희석비 & 사용 가이드

Ethos Car Care 맥스 그래핀 코팅 희석비 pH 스펙 카드

MAX Graphene Coating

V2.0 대비 약 225% 더 높은 레진 함량과 강화 첨가제를 적용해 일상 주행 차량, 휠, 산업용 등 고마모 환경을 위한 헤비듀티 그래핀 코팅입니다. 두꺼운 반영구 코팅막을 형성해 브랜드 기준 약 7년 이상의 내구성, 높은 접촉각, 강한 스크래치·워터스팟 저항성을 제공합니다. 플래시 타임이 빠르고 막이 두꺼워 어느 정도 시공 경험이 있는 사용자에게 권장됩니다.

브랜드
Ethos Car Care
카테고리
Exterior : Coating
기본 희석 비율
RTU
최종 업데이트
2026-06-02

핵심 특징

희석 비율

용도희석비율
Exterior : Coating (기본)RTU1:0

사용법

  1. 차량을 세차한 뒤 클레이 바로 박힌 오염물을 제거하고, 봉인되기 전에 폴리싱으로 결함을 정리합니다.
  2. 에토스 디톡스로 폴리시 오일과 잔여물을 닦아내고 틈새의 물기까지 모두 제거합니다.
  3. 병을 흔든 뒤 어플리케이터에 코팅제를 몇 방울 떨궈 고르게 적십니다.
  4. 수평면부터 약 60cm × 60cm 구획으로 살짝 겹치는 직선으로 도포합니다.
  5. 약 30초~1분 두어 레인보우가 흐릿한 안개로 변하면 닦아낼 준비가 된 것입니다.
  6. 부드러운 마이크로파이버로 작은 원을 그리며 가볍게 잔여물을 모두 닦아냅니다.
  7. 손전등으로 옆 패널의 밀린 잔여물을 점검한 뒤 다음 구역으로 이동해 차량 전체에 반복합니다.
  8. 추가 도포는 최소 1시간 간격을 두고, 도포 후 48시간 이상 물에 닿지 않게 합니다.

Heavy-duty graphene coating built with the brand’s highest resin solids content — about 225% more than V2.0 — plus extra additives, aimed at daily drivers, wheels, and high-wear or industrial use. It forms a thick semi-permanent layer that the brand rates for roughly 7 years or more, with a high contact angle and solid resistance to scratching and water spotting. The faster flash time and thicker film make it better suited to users with some coating experience.

Key features

  • High-solids DIY graphene coating
  • About 7 years or more per brand
  • 118 degree contact angle
  • Scratch and water spot resistance
  • Built for daily drivers and high-wear use
  • Use on paint, glass, plastic, or wheels

Usage

  1. Wash the car, then clay bar embedded contaminants and polish out defects before they get sealed in.
  2. Wipe down with Ethos Detox to clear polish oils and residues, and dry any water trapped in gaps.
  3. Shake the bottle and put a few drops onto the applicator until it is evenly wet.
  4. Work roughly 2 ft by 2 ft sections starting on horizontal surfaces, laying slightly overlapping straight lines.
  5. Wait about 30 seconds to 1 minute until the rainbow look turns to a haze, ready for removal.
  6. Wipe the section with a soft microfiber in small circles using light pressure to clear all residue.
  7. Check adjacent panels with a flashlight for pushed residue, then continue around the vehicle.
  8. Wait at least an hour between coats and keep the surface dry for a minimum of 48 hours to cure.

다른 이름: 에토스, 이토스, ethos, Ethos MAX Graphene Coating, MGC, Ethos MGC, 에토스 맥스 그래핀 코팅, 에토스 MGC

View in English

출처

관련 제품

Ethos Car Care의 다른 제품

같은 카테고리(Coating) 제품

더 보기