MAX Graphene Coating
맥스 그래핀 코팅
Heavy-duty graphene coating built with the brand's highest resin solids content (225% more than V2.0) plus additional additives, intended for daily drivers, wheel surfaces, and high-wear or industrial applications. Forms a thick, semi-permanent layer with up to 7+ years of durability, a high contact angle, and strong resistance to scratching and water spotting. Aimed at advanced users due to its faster flash time and thicker film.
V2.0 대비 225% 더 높은 레진 함량과 강화 첨가제를 적용해 일상 주행 차량, 휠, 산업용 등 고마모 환경을 위한 헤비듀티 그래핀 코팅입니다. 두꺼운 반영구 코팅막을 형성해 최대 7년 이상의 내구성, 높은 접촉각, 강한 스크래치·워터스팟 저항성을 제공합니다. 플래시 타임이 빠르고 막이 두꺼워 어느 정도 시공 경험이 있는 사용자에게 권장됩니다.
- Brand
- Ethos Car Care
- Categories
- Exterior : Coating
Key features
- Highest resin solids DIY coating
- 7+ year durability rating
- 118 degree contact angle
- Scratch and water spot resistance
- For daily drivers and high-wear use
- Compatible with paint, glass, plastic, wheels
Usage
- Wash the vehicle, then clay bar embedded contaminants and polish out paint defects since they will be sealed under the coating.
- Wipe the surface down with Ethos Detox to remove polish oils and residues, and dry any trapped water from gaps.
- Shake the bottle and apply a few drops onto the applicator until evenly covered.
- Work in roughly 2 ft by 2 ft sections starting with horizontal surfaces, laying down even slightly overlapping straight lines.
- Wait roughly 30 seconds to 1 minute until the rainbow effect transitions to a haze, signaling the coating is ready to remove.
- Wipe the section with a premium microfiber using small circular motions and light pressure to remove all residue.
- Inspect adjacent panels for pushed residue with a flashlight, then move on and repeat across the vehicle.
- Wait at least one hour between coats and keep the surface dry for 48 hours minimum to cure.
핵심 특징
- DIY 코팅 중 최고 수준 레진 함량
- 7년 이상 내구성
- 접촉각 118도
- 스크래치·워터스팟 저항
- 일상 주행·고마모 환경 대응
- 도장면·유리·플라스틱·휠 호환
사용법
- 차량을 세차한 뒤 클레이 바로 박힌 오염물을 제거하고, 결함은 코팅 후 봉인되므로 폴리싱으로 사전에 정리합니다.
- 에토스 디톡스로 표면의 폴리시 오일과 잔여물을 닦아내고, 틈새의 물기도 완전히 제거합니다.
- 병을 흔든 뒤 어플리케이터에 코팅제를 몇 방울 떨어뜨려 고르게 적십니다.
- 수평 표면부터 약 60cm × 60cm 구획으로 작업하며 살짝 겹치는 직선으로 도포합니다.
- 30초~1분 정도 기다려 레인보우 효과가 흐릿한 안개로 변하면 닦아낼 준비가 된 것입니다.
- 고급 마이크로파이버로 작은 원을 그리며 가볍게 닦아 잔여물을 모두 제거합니다.
- 손전등으로 인접 패널의 밀린 잔여물을 점검한 뒤 다음 구역으로 이동해 차량 전체에 반복합니다.
- 추가 도포는 최소 1시간 간격을 두고, 도포 후 48시간 이상 물에 닿지 않게 건조시킵니다.