Wrap-PPF 2.0
랩-PPF 2.0
Wax is Dead Wrap-PPF 2.0 · 왁스 이즈 데드 랩-PPF 2.0
Wrap-PPF 2.0 is a consumer-grade single-layer ceramic coating applied on top of vinyl wrap and paint protection films, forming a durable, hydrophobic, and chemical-resistant barrier lasting up to 24 months. Its UV inhibitors prevent fading and discolouration of wrap films, graphics, and decals, while the superhydrophobic layer repels dirt and contaminants to make maintenance easier and extend the life of the underlying film.
Wrap-PPF 2.0는 비닐 랩 및 페인트 보호 필름(PPF) 위에 시공하는 소비자용 단일 레이어 세라믹 코팅으로, 최대 24개월간 지속되는 내구성 있는 발수·내화학성 보호막을 형성합니다. 자외선 차단 성분이 랩 필름, 그래픽, 데칼의 탈색과 변색을 방지하며, 초발수 레이어가 오염물과 먼지를 차단하여 유지 관리를 용이하게 하고 필름 수명을 연장합니다.
- Brand
- Wax is Dead
- Categories
- Exterior : Coating
Key features
- Single-layer ceramic coating for vinyl wrap and PPF
- Up to 24 months protection durability
- Superhydrophobic with exceptional water beading
- High chemical resistance
- UV inhibitors prevent fading and discolouration
- Enhances gloss, matte, and satin finishes
- Protection against superficial scratches and swirl marks
- Withstands temperatures up to 760°C
Usage
- Shake the bottle thoroughly before use.
- Ensure the surface is completely dry and free from contaminants, sealants, waxes, and oils.
- Apply approximately 7–10 drops onto the applicator pad and spread evenly across a maximum 2ft × 2ft section in a cross-hatch motion.
- Do not attempt to coat large panels such as an entire bonnet in a single pass.
- Watch for the coating to flash (disperse), then wipe off residue with a soft microfibre cloth within 5–60 seconds depending on temperature and humidity.
- For matte finishes, use a two-pass process: the first to apply the coating and the second to level it, as matte surfaces absorb faster than gloss.
- Repeat on every panel to ensure full surface coverage.
- Keep the coated surface away from moisture for 24 hours to allow initial curing.
- Wait at least 2 weeks before washing to allow the coating to fully cure.
핵심 특징
- 비닐 랩 및 PPF 전용 단일 레이어 세라믹 코팅
- 최대 24개월 내구성 보호
- 뛰어난 물방울 맺힘 효과의 초발수성
- 높은 내화학성
- 자외선 차단 성분으로 탈색 및 변색 방지
- 광택, 무광, 새틴 마감 향상
- 미세 스크래치 및 소용돌이 흠집 방지
- 최대 760°C 내열성
사용법
- 사용 전 병을 충분히 흔드세요.
- 시공 전 표면이 완전히 건조되어 있고 오염물, 실란트, 왁스, 오일이 없는 상태인지 확인하세요.
- 어플리케이터 패드에 코팅제를 7~10방울 떨어뜨린 후, 최대 60×60cm(2ft×2ft) 구역을 격자 방향으로 고르게 도포하세요.
- 보닛 전체와 같은 넓은 패널을 한 번에 코팅하려 하지 마세요.
- 코팅제가 분산되는 플래싱 현상이 보이면, 온도와 습도에 따라 5~60초 이내에 부드러운 마이크로파이버 천으로 잔여물을 닦아내세요.
- 무광 마감의 경우, 코팅 도포 1회와 평탄화 1회의 2단계 시공법을 사용하세요. 무광 표면은 광택 표면보다 코팅제 흡수가 빠릅니다.
- 모든 패널에 동일한 과정을 반복하여 전체 면적을 코팅하세요.
- 초기 경화를 위해 24시간 동안 코팅 표면에 수분이 닿지 않도록 하세요.
- 코팅이 완전히 경화되도록 최소 2주간 세차를 피하세요.