C0 Aero Coat
C0 에어로 코트
C0 Aero Coat is a ceramic coating built to limit how easily contaminants stick to surfaces, originally designed for race cars and rated for up to about 2 years on road cars. It delivers strong gloss, water beading at around a 110 degree contact angle, and 6H swirl resistance on paint or gel coat. Use it on its own or as a topcoat over other Gtechniq permanent paint protection products.
C0 에어로 코트는 표면에 이물질이 잘 달라붙지 않도록 설계된 세라믹 코팅으로, 본래 레이스카용으로 개발되었으며 일반 차량에서는 최대 약 2년까지 지속됩니다. 우수한 광택과 약 110도 접촉각의 발수 성능, 6H 수준의 스월 내성을 페인트와 젤코트 위에서 발휘합니다. 단독으로 사용하거나 다른 Gtechniq 영구 코팅의 탑코트로 적층할 수 있습니다.
- Brand
- GTECHNIQ
- Categories
- Exterior : Coating
Key features
- Strong anti-adhesion of contaminants
- Hydrophobic water beading
- Suited to race and track cars
- Usable as standalone or topcoat
Usage
- Shake the bottle well and apply out of direct sunlight.
- Wear gloves throughout the application.
- Dab product onto the supplied AP2 Ultra Soft Foam Filled Microfibre applicator pad.
- Replace the cap and set the bottle aside, since holding it warms the product and speeds curing.
- Work one large panel or several smaller panels at a time.
- Wait 2 to 3 minutes, then remove residue with an MF1 ZeroR cloth and follow up with an MF6 Haze Buster or another MF1.
- Rotate cloths quickly so the coating does not partially cure into the fabric.
- If residue cures fully, polish the area and reapply the coating.
- Immediately after finishing, soak microfibres in water and wash and dry them right away to prevent crystallisation.
- Allow the coating to cure for 12 hours before exposing the car to the elements.
- Store in a cool, dry place.
- Use within 3 months of opening.
핵심 특징
- 오염물 부착 억제
- 발수 성능
- 레이스 및 트랙 차량에 적합
- 단독 또는 탑코트로 사용 가능
사용법
- 사용 전 잘 흔들고 직사광선을 피해 시공합니다.
- 작업 중에는 장갑을 착용합니다.
- 동봉된 AP2 울트라 소프트 폼 어플리케이터 패드에 제품을 묻혀줍니다.
- 뚜껑을 닫아 한쪽에 두며, 손에 오래 들고 있으면 조기 경화될 수 있어 주의합니다.
- 큰 패널 한 면 또는 작은 패널 여러 개를 한 번에 작업합니다.
- 2~3분 후 MF1 ZeroR 천으로 잔여물을 제거하고, MF6 헤이즈 버스터나 다른 MF1으로 한 번 더 버핑합니다.
- 천에 코팅이 부분 경화되지 않도록 자주 깨끗한 천으로 교체합니다.
- 잔여물이 완전히 경화되었다면 해당 부위를 폴리싱한 뒤 코팅을 다시 도포합니다.
- 작업 직후 마이크로파이버 천을 물에 담가 빠르게 세척하고 건조해 결정화를 막습니다.
- 차량을 외부에 노출하기 전 12시간 동안 경화시킵니다.
- 서늘하고 건조한 장소에 보관합니다.
- 개봉 후 3개월 이내에 사용합니다.