Vanguard Inorganic Crystals Coating For Car Paint User Guide

Vanguard Inorganic Crystals Coating For Car Paint dilution ratio and pH specification chart

이노가닉 크리스탈 코팅 포 카 페인트

Vanguard Inorganic Crystals Coating For Car Paint — Exterior : Coating. See full specs and usage on the Find Your Detail product page: https://findyourdetail.io/products/vanguard/inorganic-crystals-coating-for-car-paint

Vanguard 이노가닉 크리스탈 코팅 포 카 페인트 — Exterior : Coating. 전체 사양·사용법은 Find Your Detail 제품 페이지에서 확인하세요: https://findyourdetail.io/products/vanguard/inorganic-crystals-coating-for-car-paint

A high-silicon inorganic crystal coating for car paint that cures into a hard, glossy, and highly water-repellent protective layer. It is built for lasting durability and can be paired with matching glass and plastic coatings from the same range for a thicker combined film.

고농도 무기 실리콘 성분의 크리스탈 코팅제로, 도장면에 단단하고 광택이 뛰어나며 발수력이 강한 보호막을 형성합니다. 내구성이 뛰어나며 동일 시리즈의 유리·플라스틱 코팅제와 함께 시공하면 더욱 두꺼운 보호층을 만들 수 있습니다.

Brand
Vanguard
Categories
Exterior : Coating
Last updated
2026-07-13

Key features

Usage

  1. Wash the car thoroughly.
  2. Remove tar and other embedded stains with a stain remover.
  3. Use a brake dust remover and clay to strip remaining residue and dust particles.
  4. Polish the paint, working from a coarser to a finer compound to prepare the surface.
  5. Wipe down with a degreaser to remove polishing residue before coating.
  6. Place a few drops of coating on the applicator sponge and wipe it over roughly a 40x40cm section, first horizontally then vertically.
  7. Note the time it takes for the coating to show resistance when wiped with a towel, then use that same timing to coat the rest of the car from front to back and top to bottom.
  8. Check the entire car for any uncured coating residue.
  9. Let the vehicle sit indoors for at least 2-3 hours without water contact or touching the surface before returning it.

핵심 특징

  • 고농도 무기 실리콘 성분
  • 높은 경도와 광택
  • 강력한 발수 효과
  • 뛰어난 지속성과 안정성
  • 유리·플라스틱 코팅제와 중첩 시공 가능

사용법

  1. 차량 전체를 꼼꼼히 세차합니다.
  2. 스테인 리무버로 타르 등 찌든 오염을 제거합니다.
  3. 브레이크 더스트 리무버와 클레이로 남은 이물질과 분진을 제거합니다.
  4. 거친 것부터 고운 것 순으로 컴파운드를 사용해 도장면을 폴리싱합니다.
  5. 탈지제로 폴리싱 잔여물을 닦아내 코팅 전 표면을 정리합니다.
  6. 어플리케이터 스펀지에 코팅제를 몇 방울 떨어뜨려 가로, 세로 방향으로 약 40x40cm 구역씩 도포합니다.
  7. 천으로 닦았을 때 저항감이 느껴지는 시점을 확인한 뒤, 같은 타이밍으로 차량 전체를 앞뒤·위아래 순서로 시공합니다.
  8. 차량 전체를 점검해 굳지 않은 코팅 잔여물이 없는지 확인합니다.
  9. 시공 후 최소 2~3시간 동안 실내에 보관하며 물이 닿거나 표면을 만지지 않도록 합니다.

Also known as: 뱅가드, Vanguard Inorganic Crystals Coating For Car Paint, 뱅가드 이노가닉 크리스탈 코팅 포 카 페인트, RH-5064

한국어로 보기

Sources

Related products

More from Vanguard

More Coating products

Explore more