Plastic Coat -matt-
플라스틱 코트 매트
serv · 서브페이스 · 서브 · servFaces Plastic Coat -matt- · SF Plastic Coat -matt- · Plastic Coat matt · 서브페이시스 플라스틱 코트 매트 · SF10179.1
A transparent, high-strength coating for untreated plastic surfaces that gives a semi-gloss look rather than a high shine. It forms a long-lasting, dirt-resistant film that holds up to temperatures around 680°C without losing its fireproof properties and resists ordinary cleaners. A built-in UV blocker offers extended protection against plastic discoloration.
미처리 플라스틱 표면을 위한 투명 고강도 코팅으로 고광택 대신 반광택 마감을 줍니다. 오염에 강한 지속성 피막을 형성하고 약 680°C까지 내화 특성을 유지하며 일반 세정제에도 잘 견딥니다. UV 차단 성분이 플라스틱의 변색을 오래 막아줍니다.
- Brand
- servFaces
- Categories
- Exterior : Coating, Interior : Trim Sealants
Key features
- High-strength transparent coating for untreated plastics
- Gives a semi-gloss finish
- Resists dirt and easy to clean
- Heat-resistant to around 680°C without affecting fireproof properties
- Resists ordinary cleaners
- Built-in UV blocker for long-term discoloration protection
- Flexible film up to 5 µm that does not chip or peel
- Can be applied by fine compressed-air spraying
Usage
- Clean the surface with Surface Cleaner Ultima, then neutralize with Surface Cleaner Neutra.
- Fit the application cloth onto the applicator.
- Put 12 to 18 drops of Plastic Coat -matt- on the cloth and spread it quickly in sections of up to 50 x 50 cm to form a visible film.
- Let it react for about 1 to 3 minutes depending on amount, humidity, and temperature.
- Remove the excess with a Special Coating Towel, working from the edges inward with straight, quick strokes.
- Polish with a fresh Special Coating Towel under light pressure, from the edges inward in circles.
- If streaks remain, repeat the polishing step with another fresh Special Coating Towel until clear.
- Recoating is possible after 20 minutes but should be completed within 35 minutes.
핵심 특징
- 미처리 플라스틱용 고강도 투명 코팅
- 반광택 마감
- 오염에 강하고 세정 용이
- 내화 특성을 유지하며 약 680°C까지 내열
- 일반 세정제에 잘 견딤
- 장기 변색 방지 UV 차단 성분 내장
- 5µm까지의 유연한 피막, 박리나 벗겨짐 없음
- 압축 공기 미세 분사 도포 가능
사용법
- 서피스 클리너 울티마로 표면을 닦은 뒤 서피스 클리너 뉴트라로 중화합니다.
- 어플리케이터에 도포 클로스를 끼웁니다.
- 플라스틱 코트 매트를 12~18방울 클로스에 떨어뜨리고 최대 50x50cm 구역씩 빠르게 펴 발라 눈에 보이는 피막을 만듭니다.
- 도포량, 습도, 온도에 따라 약 1~3분간 반응시킵니다.
- 스페셜 코팅 타월로 가장자리부터 안쪽으로 직선의 빠른 동작으로 잉여 제품을 닦아냅니다.
- 새 스페셜 코팅 타월로 약한 압력을 주며 가장자리부터 안쪽으로 원을 그리며 닦습니다.
- 얼룩이 남으면 새 스페셜 코팅 타월로 깨끗해질 때까지 반복합니다.
- 재코팅은 20분 후 가능하며 35분 이내에 마쳐야 합니다.