Coat Ultima
코트 울티마
serv · 서브페이스 · 서브 · servFaces Coat Ultima · SF Coat Ultima · CU · servFaces CU · SF CU · 서브페이시스 코트 울티마 · 서브페이시스 CU · SF10332
A very hard hybrid SiO2-polymer ceramic coating that gives painted surfaces lasting protection with little application effort. Its molecular-matrix structure chemically bonds to the paint, raising surface hardness by roughly 60 to 65 percent. Once cured it brings strong gloss and water beading along with resistance to salt, acids, oxidation, and insect residue.
하이브리드 SiO2 폴리머 세라믹 코팅으로, 적은 작업량으로 도장면을 오래 보호합니다. 분자 매트릭스 구조가 도료와 화학적으로 결합해 표면 경도를 약 60~65% 높여 줍니다. 경화 후에는 강한 광택과 발수성을 내며 염분과 산, 산화, 벌레 잔여물로부터 도장을 지켜 줍니다.
- Brand
- servFaces
- Categories
- Exterior : Coating
Key features
- Hard hybrid SiO2-polymer coating
- Molecular-matrix structure bonds chemically to paint
- Surface hardness increase of about 60 to 65 percent
- High-gloss protective layer after curing
- Dirt-repellent anti-adhesion surface
- Gloss guarantee of 5 to 10 years for professional use
- Recoatable within 20 to 35 minutes
Usage
- Clean the surface with Surface Cleaner Ultima, then neutralize with Surface Cleaner Neutra.
- Place the application cloth on the applicator.
- Apply 12–18 drops of Coat Ultima to the cloth and spread quickly over one panel section at a time (max half a bonnet), ensuring a visible film forms.
- Allow the product to react for approximately 1–3 minutes depending on quantity applied, ambient humidity, and temperature.
- Remove surplus material with a fresh Special Coating Towel, starting at peripheral areas and working inward with straight quick movements.
- Buff the surface with another clean Special Coating Towel using light circular pressure, again starting at edges and working inward.
- If streaks remain, repeat buffing with a new towel until the surface is clear (check with a light source).
- For a second coat, reapply after 20 minutes but no later than 35 minutes.
핵심 특징
- 단단한 하이브리드 SiO2 폴리머 코팅
- 도장면과 화학적으로 결합하는 분자 매트릭스 구조
- 표면 경도 약 60~65% 향상
- 경화 후 고광택 보호층
- 오염 방지 논스틱 표면
- 전문가 사용 기준 5~10년 광택 보증
- 20~35분 이내 재코팅 가능
사용법
- Surface Cleaner Ultima로 표면을 세정한 후 Surface Cleaner Neutra로 중화합니다.
- 어플리케이터 위에 도포 천을 올립니다.
- 천에 코트 울티마를 12~18방울 떨어뜨린 뒤, 한 번에 한 패널 섹션씩(최대 보닛 절반) 신속히 고르게 펼쳐 눈에 보이는 피막이 형성되도록 합니다.
- 도포량·습도·온도에 따라 약 1~3분간 제품이 반응하도록 둡니다.
- 새 Special Coating Towel로 남은 재료를 제거합니다. 가장자리부터 시작해 직선 동작으로 안쪽으로 작업합니다.
- 깨끗한 Special Coating Towel로 가볍게 압력을 주며 원형 동작으로 표면을 버핑합니다. 가장자리에서 안쪽 방향으로 진행합니다.
- 줄무늬가 남아 있으면 새 타월로 반복 버핑하여 광원 확인 후 완전히 제거합니다.
- 2회 도포 시에는 20분 후, 최대 35분 이내에 재코팅합니다.