PAICAR 01 헤비 컷 희석비 & 사용 가이드

PAICAR 01 헤비 컷 희석비 pH 스펙 카드

01 Heavy Cut

01 헤비 컷은 심한 스월 마크, 중간 깊이의 스크래치, P1500~P2000 범위의 샌딩 자국을 다루는 수성 컴파운드입니다. 작업성이 잘 잡혀 있어 부가적인 마링을 억제하면서 결함을 단계적으로 제거할 수 있습니다. 강한 보정에는 로터리 폴리셔, 깔끔한 마감에는 듀얼 액션 폴리셔와 함께 쓸 수 있고 잔여물도 쉽게 닦입니다.

브랜드
PAICAR
카테고리
Exterior : Polishes
기본 희석 비율
RTU
최종 업데이트
2026-06-02

핵심 특징

희석 비율

용도희석비율
Exterior : Polishes (기본)RTU1:0

사용법

  1. 표면을 세차하고 필요하면 클레이 바로 완전히 오염을 제거한 뒤 패널을 완전히 건조시킵니다.
  2. 강한 보정에는 로터리 폴리셔에 마이크로파이버 패드를, 더 나은 마감에는 듀얼 액션 폴리셔에 중간 폼 패드를 사용합니다.
  3. 잘 흔든 뒤 패드에 3~4방울을 떨어뜨리고 기계를 끈 상태에서 패널에 펴 발라줍니다.
  4. 최저 속도로 시작해 속도를 올려 연마력을 살리고, 약 40×40cm 구역을 패드를 평평히 한 채 가벼운 압력으로 교차 패스합니다.
  5. 3~4회 패스(약 2분) 후 깨끗한 마이크로파이버 타올로 잔여물을 닦고 검사등으로 결함 제거를 확인합니다.
  6. 필요하면 마무리 폴리시로 다듬은 뒤 실란트나 왁스로 표면을 보호합니다.

01 Heavy Cut is a water-based compound for paint correction, tackling heavy swirl marks, moderate scratches and sanding marks in the P1500 to P2000 range. Its controlled workability lets you remove defects gradually while keeping secondary marring low. It works with rotary polishers for stronger correction and dual action polishers for a cleaner finish, and it wipes off easily.

Key features

  • Corrects heavy swirl marks, moderate scratches and visible defects
  • Removes P1500 to P2000 sanding marks
  • Works with rotary and dual action polishers
  • Water-based formula with controlled workability
  • Gradual defect removal with low secondary marring
  • Wipes off easily to shorten working time
  • Cut level 9/10, finish level 6/10

Usage

  1. Wash and fully decontaminate the surface, using a clay bar if needed, then dry the panel completely.
  2. For stronger correction use a microfiber pad on a rotary polisher; for a better finish use a medium foam pad on a dual action polisher.
  3. Shake well, apply 3 to 4 drops to the pad, and spread over the panel with the machine off.
  4. Start at the lowest speed, then raise it to engage the abrasive, working cross-hatch passes over roughly 40 by 40 cm with light pressure and the pad flat.
  5. After 3 to 4 passes (about 2 minutes), wipe residue with a clean microfiber towel and check defect removal under an inspection light.
  6. If needed, refine with a finishing polish, then protect the surface with a sealant or wax.

다른 이름: PAI, 파이카, 파이, PAICAR 01 Heavy Cut, HC, PAICAR HC, 파이카 01 헤비 컷, 파이카 HC

View in English

출처

관련 제품

PAICAR의 다른 제품

같은 카테고리(Polishes) 제품

더 보기