NL272
엔엘272
나지올 · Nasiol NL272 · 나시올 엔엘272
NL272 is a premium single-layer nano ceramic coating that bonds to vehicle paintwork, hard plastics, headlights, taillights, and rims to deliver 10H hardness, ultra-high gloss, and superior hydrophobic protection. Designed for professional detailers, it offers up to five or more years of durability while enhancing the depth and clarity of the original paint color.
NL272는 차량 도장면과 플라스틱·라이트·림에 단일 레이어로 시공하는 프리미엄 나노 세라믹 코팅입니다. 10H 경도, 초고광택, 강력한 발수 성능을 제공하며, 전문 디테일러를 위해 설계되어 최대 5년 이상 내구성을 자랑합니다.
- Brand
- Nasiol
- Categories
- Exterior : Coating
- Primary dilution
- RTU
Key features
- High Definition Gloss (HDR) finish
- 10H long-lasting scratch resistance
- Complete protection with a single coating layer
- Extreme durability of 5+ years
- Recommended for professional detailers
Dilution
- Exterior : Coating — RTU (1:0) (primary)
Usage
- Wash the vehicle thoroughly and apply a clay bar if needed.
- Polish and compound using silicone/wax-free compounds, then wash and dry completely; use compressed air to remove water from trims and joints.
- Wipe the surface with Nasiol Clean to improve coating adhesion; ensure the surface is free of residual contamination.
- Wearing the nitrile gloves, place a suede cloth on the applicator block. Shake the product gently, then pour 4–5 mL per 1 m² onto the cloth; keep the lid closed when not in use.
- Work on no more than 1 m² at a time. Spread the product in a crisscross motion. Replace the suede cloth every 3–4 panels.
- Once water beading appears (approx. 30 seconds), wipe off excess with the light gray microfiber cloth using linear strokes.
- Buff the surface with the dark gray microfiber cloth in circular motions to finish.
- Keep the coated surface away from water and contaminants for 24 hours; allow 48 hours for full chemical and abrasion resistance before detergent-based washing.
핵심 특징
- 고선명 글로스(HDR) 마감
- 10H 지속적 스크래치 저항성
- 단일 코팅 레이어로 완전한 보호
- 5년 이상의 탁월한 내구성
- 전문 디테일러 권장 제품
사용법
- 차량을 깨끗이 세차하고 필요한 경우 클레이 바로 오염을 제거합니다.
- 실리콘·왁스 성분이 없는 컴파운드로 폴리싱 후 세차하고 완전히 건조합니다. 압축 공기로 몰딩·이음새의 수분을 제거합니다.
- Nasiol Clean으로 표면을 닦아 코팅 접착력을 높이고 잔여 오염이 없는지 확인합니다.
- 니트릴 장갑을 착용하고 어플리케이터 블록에 스웨이드 천을 올린 뒤 제품을 가볍게 흔들고 1 m²당 4–5 mL를 도포합니다. 미사용 시 뚜껑을 닫습니다.
- 1 m² 이하 구역에 크로스 방향으로 제품을 펴 바릅니다. 스웨이드 천은 3–4개 패널마다 교체합니다.
- 물방울 맺힘이 시작되면(약 30초) 밝은 회색 마이크로파이버 천으로 직선 방향으로 잔여물을 닦아냅니다.
- 짙은 회색 마이크로파이버 천으로 원형 동작으로 마무리 버핑합니다.
- 24시간 수분·오염물질 차단, 48시간 후 내화학성 완전 발현 및 샴푸 세차 가능합니다.