Koch Chemie Ceramic Body Cb0.01 Dilution Ratios & User Guide
세라믹 바디 Cb0.01
Koch Chemie Ceramic Body Cb0.01 — Exterior : Coating. See full specs and usage on the Find Your Detail product page: https://findyourdetail.io/products/koch-chemie/ceramic-body-cb0-01
Koch Chemie 세라믹 바디 Cb0.01 — Exterior : Coating. 전체 사양·사용법은 Find Your Detail 제품 페이지에서 확인하세요: https://findyourdetail.io/products/koch-chemie/ceramic-body-cb0-01
Long-life ceramic coating for painted bodywork on cars, vans, motorcycles, RVs, and boats. Becomes weather-resistant after about 24 hours and reaches full cure roughly nine days later. Application requires properly polished, freshly degreased paint to avoid adhesion problems.
승용차·상용차·모터사이클·캠핑카·보트 도장 외관에 사용하는 장기 보호용 세라믹 코팅입니다. 약 24시간이 지나면 내후성이 형성되고 9일 정도가 지나야 완전히 굳습니다. 시공 전에는 도장면을 충분히 폴리싱하고 탈지해 두어야 부착 문제가 생기지 않습니다.
- Brand
- Koch Chemie
- Categories
- Exterior : Coating
- Primary dilution
- RTU
- Where to buy
- Search on Amazon (US)
- Last updated
- 2026-08-14
How it works
- Polysilazane — Cures into a hard inorganic film.
- Amino-functional silicone — Bonds more strongly to the surface for longer durability.
Disclosed ingredients
| Ingredient | CAS | Function |
|---|---|---|
| Organic polysilazane (cyclosilazanes, di-Me / Me hydrogen silazanes) | 475645-84-2 | Film former |
| n-Butyl acetate | 123-86-4 | Solvent |
| Siloxanes and silicones, 3-[(2-aminoethyl)amino]propyl-terminated | 102782-92-3 | Film former |
| Octamethylcyclotetrasiloxane (D4) | 556-67-2 | Silicone carrier |
Ingredients disclosed in the manufacturer's Safety Data Sheet. A safety data sheet lists hazardous components only, so this is not a full formula.
Key features
- Multi-vehicle paint coating
- Weatherproof after ~24 h, full cure ~9 days
- Approx. 15-30 ml per car
- Apply with sponge or block + towel
Dilution
| Use | Dilution | Ratio |
|---|---|---|
| Exterior : Coating (primary) | RTU | 1:0 |
Usage
- Wash with an alkaline cleaner such as Green Star at 1:10, and pretreat heavy contamination with clay bar or Teerwäsche A as needed.
- Correct the paint with Heavy Cut or Fine Cut depending on condition, then refine with Micro Cut on an orbital to remove holograms.
- Wipe panels with Silicon- & Wachsentferner or Panel Preparation Spray; on sensitive single-stage paint, dilute the wax remover 1:4 with distilled water.
- Wear gloves from this point so palms cannot contaminate the prepared paint.
- Charge the Application Sponge (or block plus Application Towel) with Cb0.01 and lay two cross coats panel by panel until a thin, closed liquid film is visible.
- Let the coating flash off, then buff with the Coating Towel: lift the excess first, then lightly polish with the fresh side of the towel using circular motions.
- Skip washing for at least nine days; gently lift bird droppings and insects right away, and add Spray Sealant S0.02 or Hand Wax W0.01 after 24 hours as a topper.
핵심 특징
- 다양한 차종 도장면 코팅
- 약 24시간 내후성, 9일 완전 경화
- 차량 1대당 약 15~30ml
- 스폰지 또는 블록+타월로 시공
사용법
- 그린 스타 1:10 같은 알칼리 세정제로 세차하고, 수지나 타르 등 거친 오염은 클레이바나 Teerwäsche A로 먼저 정리합니다.
- 상태에 맞춰 헤비 컷이나 파인 컷으로 도장을 교정하고, 마지막에 마이크로 컷을 듀얼액션으로 돌려 홀로그램을 정리합니다.
- Silicon- & Wachsentferner나 Panel Preparation Spray로 면을 닦아 내며, 민감한 단일층 도장에는 가급적 증류수로 1:4 희석합니다.
- 이 단계 이후로는 손바닥 자국이 부착력을 망가뜨리지 않도록 장갑을 착용합니다.
- 어플리케이션 스폰지(또는 블록과 타월)에 Cb0.01을 적셔 패널 단위로 빠르게 작업하며, 두 번의 크로스 코트로 얇은 막을 형성합니다.
- 플래시 오프 시간이 지나면 코팅 타월로 잔여물을 먼저 거두고, 새 면으로 압력 없이 원을 그리며 마무리 닦아 냅니다.
- 최소 9일은 세차를 미루고 그 동안 새똥이나 벌레는 즉시 부드럽게 닦아 내며, 24시간 후에는 Spray Sealant S0.02 또는 Hand Wax W0.01을 토퍼로 올리는 것이 권장됩니다.
Also known as: KCX, koch-chemie, 코흐, 코흐케미, Cb0.01, Koch Cb0.01, KC Cb0.01, 코흐케미 Cb0.01, 세라믹 바디, Ceramic Body, 코흐 Cb0.01
Sources
Related products
More from Koch Chemie
- Dräger Combination Filter 940
- Colourlock Fresh Up
- Application Pen
- PreWash express
- Angle Washing Brush with Water Flow
- Reactivation Shampoo extra
More Coating products
- Wake Me Angel
- Dr. Beasley's Premium Paint Sealant
- Meguiar's Marine/RV Quik Wax
- EWOCAR Graphene60
- Fireball STELLA
- Auto Finesse Aqua Coat