P1 Polish Up
P1 폴리시 업
innova · 이노바 · 이노바카 · Innovacar P1 Polish Up · IC P1 Polish Up · P1PU · Innovacar P1PU · IC P1PU · 이노바카 P1 폴리시 업 · 이노바카 P1PU · 79187
P1 Polish Up is a silicone-free finishing polish formulated to remove micro-scratches, swirl marks, and holograms from automotive paintwork. Its fine abrasives clear surface oxidation to restore colour and gloss, and it works with both rotary and rotary-orbital polishers. It leaves a high-gloss finish and prepares the surface for a sealant or wax.
P1 폴리시 업은 도장면의 미세 스크래치, 소용돌이 흠집, 홀로그램을 제거하도록 만든 실리콘 무함유 마감 폴리시입니다. 미세 연마 성분이 표면 산화를 제거해 색상과 광택을 복원하며, 로터리와 로터리오비탈 폴리셔 모두에 쓸 수 있습니다. 높은 광택으로 마무리하고 실란트나 왝스 도포 전 표면을 준비시켜 줍니다.
- Brand
- Innova Car
- Categories
- Exterior : Polishes
Key features
- Removes micro-scratches and polishing errors
- Clears swirl marks and holograms
- Restores colour and finish by removing oxidation
- High-gloss result
- Silicone-free formula
- Works with rotary and rotary-orbital polishers
- Prepares surface for sealant or wax
Usage
- Complete all preliminary steps (pre-washing, washing, chemical and mechanical decontamination) before polishing.
- Shake the product before use.
- Attach the pad firmly and centrally to the polisher plate.
- Apply a suitable amount onto a medium-soft blue sponge pad; use more on a new pad, and ensure a used pad is clean.
- Drape the polisher cable over your shoulder to prevent bodywork damage.
- Start and stop the polisher with the pad in contact with the surface to avoid splashing.
- Polish at 800 RPM over a small area of about 60x40 cm, horizontally then vertically, overlapping each pass by 50%.
- Gradually increase speed up to 2000 RPM and work the area again for an even finish.
- Remove residue with a microfibre cloth and check the result with D2 Check, then continue across all desired areas.
핵심 특징
- 미세 스크래치 및 폴리싱 오류 제거
- 소용돌이 흠집 및 홀로그램 제거
- 산화 제거로 색상 및 마감 복원
- 높은 광택 결과
- 실리콘 무함유 포뮬라
- 로터리 및 로터리오비탈 폴리셔 호환
- 실란트 또는 왝스 도포 전 표면 준비
사용법
- 폴리싱 전 사전 세차, 세차, 화학적·기계적 오염 제거 등 모든 준비 작업을 마칩니다.
- 사용 전 제품을 충분히 흔듭니다.
- 패드를 폴리셔 플레이트 정중앙에 단단히 부착합니다.
- 중간 부드러운 파란색 스펀지 패드에 적당량을 바릅니다. 새 패드에는 더 많은 양을 쓰고, 재사용 패드는 깨끗이 세척해 사용합니다.
- 도장면 손상을 막기 위해 폴리셔 코드를 어깨에 걸쳐 둡니다.
- 튐을 막기 위해 패드를 표면에 밀착한 상태에서 전원을 켜고 끕니다.
- 800 RPM으로 약 60x40cm 작은 구역을 수평으로 먼저, 이어 수직으로 50% 겹쳐 작업합니다.
- 속도를 2000 RPM까지 서서히 높이며 같은 구역을 재작업해 균일하게 마감합니다.
- 마이크로파이버 천으로 잔여물을 제거하고 D2 체크로 결과를 확인한 뒤 원하는 전 구역에 동일하게 진행합니다.