G1 ClearVision Smart Glass
G1 클리어비전 스마트 글래스
G1 ClearVision Smart Glass is a water-repellent glass coating that bonds chemically to the surface for long-lasting performance in wet weather. It builds a smooth hydrophobic layer that beads water and rolls it off the glass, reducing wiper use and improving rain, snow, and sleet visibility. Supplied with G2 Residue Remover and durable for up to about 20,000 miles.
G1 클리어비전 스마트 글래스는 유리 표면과 화학적으로 결합해 비 오는 환경에서도 오래 지속되는 발수 코팅을 형성합니다. 매끄러운 발수 막이 물방울을 구슬처럼 맺히게 해 흘려보내므로 와이퍼 사용을 줄이고 비, 눈, 진눈깨비 상황의 시야를 개선합니다. G2 레지듀 리무버가 함께 제공되며 최대 약 20,000마일까지 지속됩니다.
- Brand
- GTECHNIQ
- Categories
- Exterior : Glass Sealant
Key features
- Hydrophobic coating
- Durable chemical bond
- Lasts up to about 20,000 miles
- Includes G2 Residue Remover
- Improves wet-weather visibility
Usage
- Work in a ventilated area at 5 degrees Celsius or above; wear gloves and avoid direct sunlight.
- Clean glass with G6 Perfect Glass and an MF5 Power Glass Cloth.
- For best results polish glass with G4 Nano Glass Polish on a medium pad (machine) or with G4 by hand in a circular motion.
- Wipe glass back to a streak-free finish with G6 and an MF5 or MF1 cloth, repeating until residue-free.
- Shake the bottle. Use 3 layers on the windscreen and 1 layer on side and rear glass.
- Apply a generous amount of G1 to an AP1 Lint-Free Applicator and work it across the glass in circles, then leave for 5 minutes to cure.
- With a fresh AP1, apply the same amount in side-to-side strokes and leave for 5 minutes.
- Apply the third layer in vertical strokes with another AP1 and leave for 15 minutes.
- Use G2 Residue Remover by dabbing it onto a remaining applicator, working a small area at a time, and buffing immediately with an MF1 cloth.
- Finish by cleaning wiper blades and glass with G6 and an MF5; you can apply a layer of G1 to wiper blades without removing residue, replacing worn blades.
- Keep the car out of the elements for at least 3 hours, store cool and dry, and use G1 and G2 within 3 months of opening.
핵심 특징
- 발수 성능
- 내구성 있는 화학 결합
- 최대 약 20,000마일 지속
- G2 레지듀 리무버 동봉
- 우천 시 시야 개선
사용법
- 5°C 이상의 통풍이 잘 되는 곳에서 작업하며 장갑을 착용하고 직사광선을 피합니다.
- 시공할 유리를 G6 퍼펙트 글래스와 MF5 파워 글래스 클로스로 깨끗이 닦습니다.
- 최적 결과를 위해 G4 나노 글래스 폴리시와 미디엄 패드로 머신 폴리싱하거나 핸드 패드로 원을 그리며 폴리싱합니다.
- G6와 MF5 또는 MF1 천으로 잔여물이 사라질 때까지 반복해 닦아 깔끔한 마감을 만듭니다.
- 병을 잘 흔들고, 앞유리는 3겹, 측·후면 유리는 1겹 도포합니다.
- AP1 린트프리 어플리케이터에 G1을 충분히 묻혀 원형으로 도포한 후 5분간 경화시킵니다.
- 새 AP1에 같은 양을 묻혀 좌우 방향으로 두 번째 층을 덧바르고 5분 더 경화시킵니다.
- 세 번째 층은 새 AP1에 같은 양을 묻혀 세로 방향으로 도포하고 15분간 경화시킵니다.
- G2 레지듀 리무버를 남은 어플리케이터에 묻혀 소구역씩 처리한 뒤 즉시 MF1 천으로 버핑합니다.
- 마지막으로 G6와 MF5로 와이퍼 블레이드와 유리를 마무리 클리닝합니다. 와이퍼 블레이드에는 잔여물 제거 없이 G1을 한 층 도포할 수 있으며, 마모된 블레이드는 교체합니다.
- 최소 3시간 동안 외부 노출을 피하고, 서늘하고 건조한 곳에 보관하며 G1과 G2는 개봉 후 3개월 이내에 사용합니다.