Graphene Coating PRO V2.0
그래핀 코팅 프로 V2.0
Professional-installer-only graphene coating that uses an advanced reduced graphene oxide composite to bond into a semi-permanent layer rated for 10 years of durability. Resists water spots, etching, oxidation, and abrasion while delivering deep gloss, and is more forgiving during install than traditional crystallizing ceramic coatings. Applicable to paint, plastic, and glass surfaces.
전문 시공자 전용으로 공급되는 그래핀 코팅으로, 환원 그래핀 옥사이드 복합 레진이 반영구적 결합을 이루어 10년 내구성을 제공합니다. 워터스팟, 에칭, 산화, 마모에 강하고 깊은 광택을 부여하며, 결정화되는 일반 세라믹 코팅보다 시공이 한층 수월합니다. 도장면, 플라스틱, 유리 등 다양한 표면에 적용 가능합니다.
- Brand
- Ethos Car Care
- Categories
- Exterior : Coating
Key features
- Graphene oxide composite coating
- 10-year durability with ASTM testing
- Hydrophobic nanocoating finish
- Reduced high spot and streak risk
- Approved installer / certified facility only
- Compatible with paint, plastic, glass
Usage
- Wash the vehicle, then clay bar embedded contaminants and polish out paint defects since they will be sealed under the coating.
- Wipe the surface down with Ethos Detox to remove polish oils and residues that could inhibit bonding.
- Shake the bottle and apply a few drops of Graphene Matrix PRO onto your applicator until evenly covered.
- Working in 3 ft by 3 ft sections starting with horizontal surfaces, lay down even slightly overlapping straight lines.
- Wait roughly 1 to 3 minutes until the rainbow effect transitions into a haze, signaling the coating is ready to remove.
- Buff the section with a premium microfiber using small circular motions and minimal pressure to remove all residue.
- Inspect adjacent panels with a flashlight for pushed residue, then move on to the next section.
- Wait 1 hour minimum (and no more than 24 hours) between coats, then allow at least 24 hours of dry cure before getting wet.
핵심 특징
- 그래핀 옥사이드 복합 코팅
- ASTM 테스트 기반 10년 내구성
- 발수 나노 코팅 마감
- 하이스팟·스트릭 위험 감소
- 공식 인증 시공자 전용
- 도장면·플라스틱·유리 호환
사용법
- 차량을 세차한 뒤 클레이 바로 박힌 오염물을 제거하고, 결함은 코팅 후 봉인되므로 폴리싱으로 사전에 정리합니다.
- 에토스 디톡스로 표면의 폴리시 오일과 잔여물을 닦아내 결합을 방해하는 요소를 없앱니다.
- 병을 흔들고 그래핀 매트릭스 PRO 몇 방울을 어플리케이터에 떨어뜨려 고르게 적십니다.
- 수평 표면부터 약 90cm × 90cm 구획으로 작업하며 살짝 겹치는 직선으로 도포합니다.
- 1~3분 정도 기다려 레인보우 효과가 흐릿한 안개로 변하면 닦아낼 준비가 된 것입니다.
- 고급 마이크로파이버로 작은 원을 그리며 가볍게 닦아 잔여물을 모두 제거합니다.
- 손전등으로 인접 패널의 밀린 잔여물을 점검하고 다음 구역으로 이동합니다.
- 추가 도포는 1시간 이상, 24시간 이내에 진행하고, 도포 후 최소 24시간은 물에 닿지 않게 건조시킵니다.