그래핀 코팅 프로 V2.0
Graphene Coating PRO V2.0
에토스 · 이토스 · ethos · Ethos Graphene Coating PRO V2.0 · 에토스 그래핀 코팅 프로 V2.0
전문 시공자 전용으로 공급되는 그래핀 코팅으로, 환원 그래핀 옥사이드 복합 레진이 반영구적으로 결합해 브랜드 기준 약 10년의 내구성을 제공합니다. 워터스팟, 에칭, 산화, 마모에 강하고 깊은 광택을 더해주며, 결정화되는 일반 세라믹 코팅보다 시공 과정이 한층 수월합니다. 도장면, 플라스틱, 유리 등 다양한 표면에 적용 가능합니다.
- 브랜드
- Ethos Car Care
- 카테고리
- Exterior : Coating
- 기본 희석 비율
- RTU
핵심 특징
- 그래핀 옥사이드 복합 코팅
- 브랜드 기준 약 10년 내구성
- 발수 나노 코팅 마감
- 하이스팟·스트릭 위험 감소
- 공식 인증 시공자 전용
- 도장면·플라스틱·유리에 적용
희석 비율
- Exterior : Coating — RTU (1:0) (기본)
사용법
- 차량을 세차한 뒤 클레이 바로 박힌 오염물을 제거하고, 봉인되기 전에 폴리싱으로 결함을 정리합니다.
- 에토스 디톡스로 폴리시 오일과 잔여물을 닦아내 결합을 방해하는 요소를 없앱니다.
- 병을 흔든 뒤 그래핀 매트릭스 PRO를 몇 방울 어플리케이터에 떨궈 고르게 적십니다.
- 수평면부터 약 90cm × 90cm 구획으로 살짝 겹치는 직선으로 도포합니다.
- 약 1~3분 두어 레인보우가 흐릿한 안개로 변하면 닦아낼 준비가 된 것입니다.
- 부드러운 마이크로파이버로 작은 원을 그리며 아주 가볍게 잔여물을 모두 닦아냅니다.
- 손전등으로 옆 패널의 밀린 잔여물을 점검한 뒤 다음 구역으로 이동합니다.
- 추가 도포는 1시간 이상 24시간 이내로 진행하고, 도포 후 최소 24시간은 물에 닿지 않게 합니다.
Installer-only graphene coating that uses a reduced graphene oxide composite to bond into a semi-permanent layer the brand rates for roughly 10 years of durability. It is designed to resist water spots, etching, oxidation, and abrasion while adding deep gloss, and the install process is more forgiving than traditional crystallizing ceramic coatings. Suitable for paint, plastic, and glass surfaces.
Key features
- Graphene oxide composite coating
- About 10-year durability per brand testing
- Hydrophobic nanocoating finish
- Reduced high-spot and streak risk
- Approved installer or certified facility only
- Use on paint, plastic, or glass
Usage
- Wash the car, then clay bar embedded contaminants and polish out paint defects before they get sealed in.
- Wipe down with Ethos Detox so polish oils and residues no longer block bonding.
- Shake the bottle and apply a few drops of Graphene Matrix PRO onto your applicator until evenly wet.
- Working 3 ft by 3 ft sections starting on horizontal panels, lay slightly overlapping straight lines.
- Wait about 1 to 3 minutes until the rainbow look turns to a haze, signaling it is ready to remove.
- Buff the section with a soft microfiber in small circles using minimal pressure to clear all residue.
- Check adjacent panels with a flashlight for pushed residue, then move to the next section.
- Wait at least 1 hour and no more than 24 hours between coats, then keep dry for at least 24 hours.