EZPZ Ceramic Coating
EZPZ 세라믹 코팅
DIY ceramic coating built on a flexible Polymersilazane molecule that combines robust protection with a long flash time and forgiving application. Performs as a stand-alone coating with 2 to 3 years of durability or as a hydrophobic topcoat over Graphene Matrix V2.0, MAX, or PRO. Engineered for extreme water repellency and reduced high spot risk for first-time users.
유연한 폴리머실라잔(Polymersilazane) 분자를 기반으로 한 DIY 세라믹 코팅으로, 견고한 보호력과 함께 긴 플래시 타임과 관대한 작업감을 제공합니다. 단독 코팅으로 사용 시 2~3년 내구성을 제공하며, 그래핀 매트릭스 V2.0, MAX, PRO 위에 발수 토퍼로도 사용할 수 있습니다. 극강의 발수성을 갖추고 하이스팟 위험을 줄여 초보자도 안심하고 시공할 수 있도록 설계됐습니다.
- Brand
- Ethos Car Care
- Categories
- Exterior : Coating
Key features
- Flexible Polymersilazane chemistry
- Stand-alone 2 to 3 year durability
- Top coat for Graphene V2.0, MAX, PRO
- Extreme hydrophobic water beading
- Long flash time, beginner friendly
- Compatible with paint, plastic, glass
Usage
- Wash the vehicle, clay bar embedded contaminants, and polish out defects since they will be sealed under the coating.
- Wipe the surface down with Ethos Detox to remove polish oils and residues that could inhibit bonding.
- Shake the bottle and apply a few drops of EZPZ onto your applicator until evenly covered.
- Working in 3 ft by 3 ft sections starting with horizontal surfaces, lay down even, slightly overlapping straight lines.
- Allow the coating to set for roughly 5 minutes after application or until the rainbow effect begins to fade.
- Wipe the section with a premium microfiber using small circular motions and light pressure while the residue is still wet and slick.
- Inspect adjacent panels with a flashlight for pushed residue, then repeat across the vehicle, waiting roughly 1 hour between additional layers.
- Allow the coating to dry and cure for at least 24 hours before exposing it to water.
핵심 특징
- 유연한 폴리머실라잔 화학 구조
- 단독 사용 시 2~3년 내구성
- 그래핀 V2.0·MAX·PRO 위 토퍼
- 극강의 발수성과 비딩
- 긴 플래시 타임으로 초보자 친화
- 도장면·플라스틱·유리 호환
사용법
- 차량을 세차한 뒤 클레이 바로 박힌 오염물을 제거하고, 결함은 코팅 후 봉인되므로 폴리싱으로 사전에 정리합니다.
- 에토스 디톡스로 표면의 폴리시 오일과 잔여물을 닦아내 결합을 방해하는 요소를 제거합니다.
- 병을 흔든 뒤 EZPZ를 몇 방울 어플리케이터에 떨어뜨려 고르게 적십니다.
- 수평 표면부터 약 90cm × 90cm 구획으로 살짝 겹치는 직선 패턴으로 도포합니다.
- 도포 후 약 5분 또는 레인보우 효과가 흐려지기 시작할 때까지 기다립니다.
- 잔여물이 아직 젖어 있고 매끄러울 때 고급 마이크로파이버로 작은 원을 그리며 가볍게 닦아냅니다.
- 손전등으로 인접 패널의 밀린 잔여물을 점검하고, 추가 레이어는 약 1시간 간격을 두고 진행합니다.
- 코팅이 충분히 경화될 수 있도록 도포 후 최소 24시간은 물에 닿지 않게 합니다.