Graphene Matrix Coating V2.0
그래핀 매트릭스 코팅 V2.0
Semi-permanent DIY ceramic coating reformulated with reduced graphene oxide (rGO) resins, additional silicates, and a low-VOC solvent for easier application. Forms a hydrophobic, scratch- and stain-resistant layer that repels water, dirt, and contaminants while drastically boosting gloss. Rated for 5+ years of durability and applicable to paint, plastic trim, and glass surfaces.
환원 그래핀 산화물(rGO) 레진과 추가 실리케이트, 저VOC 솔벤트를 사용해 도포가 한층 쉬워진 반영구 DIY 세라믹 코팅입니다. 물·먼지·오염물을 강하게 밀어내는 발수층을 형성하고, 스크래치·워터스팟·에칭에 대한 저항성을 높이며 깊은 광택을 더해줍니다. 도장면, 플라스틱 트림, 유리 전반에 사용 가능하며 5년 이상 지속됩니다.
- Brand
- Ethos Car Care
- Categories
- Exterior : Coating
Key features
- Reduced graphene oxide (rGO) resin
- 5+ year durability rating
- Hydrophobic, dirt-repellent nanocoating
- Resists water spots, etching, oxidation
- Higher 40% resin solids content
- Low-VOC solvent for faster application
- Compatible with paint, plastic, glass
Usage
- Wash the vehicle, then clay bar embedded contaminants and polish out paint defects since they will be sealed under the coating.
- Wipe the surface down with Ethos Detox to remove polish oils and residues, and dry any trapped water from panel gaps.
- Shake the bottle and apply a few drops onto the applicator until evenly saturated.
- Work 3 ft by 3 ft sections starting with horizontal panels, laying down even slightly overlapping straight lines.
- Wait roughly 1 to 3 minutes until the rainbow effect turns to a haze, indicating the coating is ready for removal.
- Wipe the section with a premium microfiber towel using small circular motions and light pressure to remove all residue.
- Inspect adjacent panels with a flashlight for any pushed residue, then move on and repeat across the rest of the vehicle.
- Wait at least one hour between additional coats and keep the surface dry for 48 hours minimum to cure.
핵심 특징
- 환원 그래핀 산화물(rGO) 레진
- 5년 이상 내구성
- 발수성·오염 차단 나노 코팅
- 워터스팟·에칭·산화 저항
- 고형분 함량 40%의 고농축 처방
- 도포가 빠른 저VOC 솔벤트
- 도장면, 플라스틱, 유리에 적용
사용법
- 차량을 세차한 뒤 클레이 바로 박힌 오염물을 제거하고, 코팅 후에는 봉인되므로 폴리싱으로 도장 결함을 사전에 제거합니다.
- 에토스 디톡스로 표면의 폴리시 오일과 잔여물을 닦아내고, 패널 틈에 남은 물기도 완전히 제거합니다.
- 병을 잘 흔든 뒤 어플리케이터에 코팅제를 몇 방울 떨어뜨려 고르게 적십니다.
- 약 90cm × 90cm 구획으로 작업하며, 수평 패널부터 시작해 직선으로 살짝 겹쳐 도포합니다.
- 도포 후 1~3분 정도 기다려 레인보우 효과가 흐릿한 안개 형태로 바뀌면 닦아낼 준비가 된 것입니다.
- 고급 마이크로파이버로 해당 구역을 작은 원을 그리듯 가볍게 닦아 잔여물을 완전히 제거합니다.
- 손전등으로 인접 패널까지 점검해 밀려난 잔여물을 확인한 뒤, 다음 구역으로 이동해 차량 전체에 반복합니다.
- 추가 도포 시 최소 1시간 간격을 두고, 코팅이 경화될 수 있도록 최소 48시간은 물에 닿지 않게 합니다.