Boats & Coats
보트 & 코트
Marine-grade graphene ceramic coating engineered for gel coat, fiberglass, and metal surfaces on boats and watercraft. Bonds into a glossy graphene oxide layer that provides multi-year UV resistance and shields against salt water, water spots, staining, and oxidation. Higher solids content delivers strong adhesion to porous gel coats with a one-coat application.
보트와 수상 장비의 젤코트, 유리섬유, 금속 표면을 위해 개발된 마린 전용 그래핀 세라믹 코팅입니다. 그래핀 옥사이드 광택층이 형성되어 자외선, 염수, 워터스팟, 산화로부터 수년간 보호하며, 세척도 한층 수월해집니다. 고형분 함량이 높아 다공성 젤코트에도 한 번의 도포로 견고하게 결합합니다.
- Brand
- Ethos Car Care
- Categories
- Exterior : Coating
Key features
- Graphene oxide marine coating
- Multi-year UV and saltwater protection
- High solids for porous gel coat bonding
- Single-coat application
- Resists water spots, stains, oxidation
- Hydrophobic, easy-rinse finish
Usage
- Clean the hull and remove loose dust, dirt, and contaminants from the surface.
- Clay bar embedded contaminants, then polish out defects since they will be sealed under the coating.
- Wipe the surface down with Ethos Detox to remove residues, and dry any trapped water from gaps.
- Shake the bottle and apply a few drops onto the applicator until evenly covered.
- Working a 3 ft by 3 ft section at a time, lay down even, slightly overlapping straight lines starting from horizontal surfaces.
- Wait roughly 1 to 3 minutes until the rainbow effect turns to a haze, signaling the coating is ready to remove.
- Buff off residue with a premium microfiber towel using small circular motions and light pressure.
- Inspect adjacent panels for pushed residue, then continue across the craft. Allow at least 48 hours of dry cure before getting wet.
핵심 특징
- 그래핀 옥사이드 마린 코팅
- 자외선·염수에 대한 다년간 보호
- 다공성 젤코트 결합용 고형분
- 단일 레이어 도포
- 워터스팟·얼룩·산화 저항
- 발수 마감으로 세척이 쉬움
사용법
- 선체를 깨끗이 세척해 표면의 먼지와 오염물을 모두 제거합니다.
- 클레이 바로 박힌 오염물을 제거하고, 결함은 코팅 아래 봉인되므로 폴리싱으로 사전에 보정합니다.
- 에토스 디톡스로 표면 잔여물을 닦아내고, 틈새에 남은 물기도 완전히 제거합니다.
- 병을 잘 흔든 뒤 어플리케이터에 몇 방울을 떨어뜨려 고르게 적십니다.
- 수평 표면부터 약 90cm × 90cm 구획으로 작업하며 살짝 겹치는 직선으로 도포합니다.
- 1~3분 정도 기다려 레인보우 효과가 흐릿한 안개로 바뀌면 닦아낼 준비가 된 것입니다.
- 고급 마이크로파이버로 작은 원을 그리며 가볍게 닦아내 잔여물을 모두 제거합니다.
- 인접 패널에 밀려난 제품을 점검하고, 도포 후 최소 48시간 동안은 물에 닿지 않게 건조시킵니다.