INSPIRE Ceramic Coating
인스파이어 세라믹 코팅
INSPIRE is a ceramic coating aimed at enthusiasts and detailers, focused on quick application and good self-cleaning behavior. It contains carbon nanotubes and graphene, which contribute to strong hydrophobicity, deep gloss and a slight darkening of the paint. The coating is rated for about 18 months or roughly 20,000 km of durability and offers good slickness as well as chemical and UV resistance.
인스파이어는 빠른 시공과 우수한 셀프 클리닝을 지향하는 세라믹 코팅입니다. 카본 나노튜브(CNT)와 그래핀이 함유되어 강한 발수성, 깊은 광택, 약간의 컬러 심화 효과를 제공합니다. 약 18개월 또는 20,000 km 정도까지 내구성이 유지되는 것으로 안내되며 슬릭한 표면감과 화학·자외선 저항성을 갖춥니다.
- Brand
- Cleantle
- Categories
- Exterior : Coating
Key features
- Quick and easy application
- Strong hydrophobicity with good durability
- Slick surface feel
- Chemical and UV resistance
- Wide application window (8–35°C, 30–80% humidity)
- Cures in about 12 hours
- Easier washing reduces use of strong chemicals
- Stated durability of about 18 months or roughly 20,000 km
- Contains graphene and carbon nanotubes (CNT)
Usage
- Shake the bottle for at least 30 seconds before use and again before each fresh application.
- Decontaminate the surface (tar, iron fallout), polish out defects if needed, then degrease with a 50% IPA solution.
- Apply in roughly 40x40 cm sections with the supplied applicator using crossing, overlapping passes (microfiber applicator for tires and rubber).
- Within 1–2 minutes, buff with a microfiber until streaks are gone; on glass and plastics also remove excess after 1–2 minutes.
- Plan coverage for a mid-size car: about 20 ml for paint, 10 ml for rims, 20 ml for glass plus plastics and tires.
- Allow at least 12 hours of bonding away from water or rain, avoid car chemicals for 5–7 days, and treat the coating as fully active after 24 hours.
- Work in a ventilated indoor space (outdoors only away from sun and strong wind), never on hot surfaces, wearing gloves and a mask.
핵심 특징
- 빠르고 쉬운 시공
- 강한 발수성과 좋은 내구성
- 매끄러운 표면감
- 화학 및 자외선 저항성
- 넓은 시공 조건(8–35°C, 습도 30–80%)
- 약 12시간 경화
- 세차가 쉬워 강한 케미컬 사용 감소
- 약 18개월 또는 20,000 km 정도 내구성
- 그래핀과 카본 나노튜브(CNT) 함유
사용법
- 사용 전 병을 30초 이상 흔들고, 매 시공 전에도 다시 흔들어 줍니다.
- 타르와 철분 오염을 제거하고 필요하면 폴리싱으로 결함을 다듬은 뒤 IPA 50% 용액으로 탈지합니다.
- 전용 어플리케이터(타이어·고무에는 마이크로파이버 어플리케이터)로 약 40x40 cm 구역씩 십자로 겹쳐 도포합니다.
- 도포 후 1–2분 안에 마이크로파이버로 스트릭이 사라질 때까지 닦아내고, 유리·플라스틱도 1–2분 후 잉여분을 제거합니다.
- 중형차 1대 기준 시공량을 잡습니다: 도장 약 20 ml, 휠 약 10 ml, 유리·플라스틱·타이어 약 20 ml.
- 최소 12시간 동안 물·비를 피하고 5–7일간 차량용 케미컬 세차를 피하며, 24시간 후를 완전 활성화 시점으로 봅니다.
- 환기가 잘 되는 실내(실외는 직사광선과 강풍을 피한 곳)에서 뜨거운 표면을 피해 시공하며 장갑과 마스크를 착용합니다.