Bilt Hamber 빌트 햄버 다이낙스-UC 희석비 & 사용 가이드

Bilt Hamber 빌트 햄버 다이낙스-UC 희석비 pH 스펙 카드

Bilt Hamber Dynax-UC

다이낙스-UC는 차량 하부와 노출된 금속 면에 얇고 거의 투명한 보호 피막을 형성하는 방청 왁스입니다. 단단한 왁스형 피막에는 금속을 찾아가는 부식 억제제가 들어 있어 기존 부식을 멈추고 새로운 부식을 늦추는 데 도움을 주며, 어두운 왁스나 언더실이 도장면 외관을 해칠 수 있는 부위에 적합합니다.

브랜드
Bilt Hamber
카테고리
Exterior : Coating
기본 희석 비율
RTU
구매(한국)
쿠팡에서 보기 — 쿠팡 파트너스 활동의 일환으로 일정 수수료를 제공받을 수 있습니다
실사용 영상
I Unpackaged A Brand New Porsche 992.2 GT3 (60-Hour Detailing Transformation) — Joe Huntley
실사용 영상
Dealer Ruined It: Correcting & Protecting a Brand New Toyota Corolla — Joe Huntley
최종 업데이트
2026-07-31

핵심 특징

희석 비율

용도희석비율
Exterior : Coating (기본)RTU1:0

사용법

  1. 언더바디와 휠하우스를 철저히 세척하고 건조시키며, 녹·먼지·유분을 모두 제거합니다.
  2. 브레이크 부품·배기계·고무 부싱·드라이브 샤프트 등을 마스킹합니다.
  3. 사용 전과 사용 중에도 에어로졸을 최소 약 2분간 흔들어 줍니다.
  4. 약 25~30cm 거리에서 노출 섀시·서스펜션 암·휠하우스 라이너에 균일하게 분사합니다. 다이낙스-UC는 UB보다 내마모성과 UV 안정성이 더 좋습니다.
  5. 약 1~2회 도포하며, 코트 간 약 30~60분의 플래시 오프 시간을 둡니다.
  6. 약 24시간 동안 완전 경화시켜, 단단하면서도 약간 유연한 피막이 돌빵과 염해에 잘 견디게 합니다.
  7. 특히 선단부와 충격이 큰 부위를 매년 점검하고 필요하면 보수 도포합니다.

Dynax-UC is an anti-corrosion wax that builds a low-thickness, near-transparent protective film for underbodies and exposed metalwork. The firm wax-like film carries metal-seeking corrosion inhibitors that help arrest existing corrosion and slow new corrosion, making it useful where dark waxes or underseal would spoil the look of bodywork.

Key features

  • Near-transparent film at about 50 microns DFT
  • Firm wax-like film resists dirt pick-up
  • Metal-seeking corrosion inhibitors
  • Safe on bare metal or painted surfaces
  • Aerosol works on its side and upside down
  • Coverage about 8-10 sq m per litre
  • Cures fully in about 24-96 hours, vehicle usable after about 30 minutes

Usage

  1. Clean and dry the underbody and wheel arches thoroughly, removing all loose rust, dirt and grease.
  2. Mask off brake components, exhaust, rubber bushes and drive shafts.
  3. Shake the aerosol for at least about 2 minutes before and during use.
  4. Spray evenly from about 25-30cm onto exposed chassis, suspension arms and wheel-arch liners; Dynax-UC is harder-wearing and more UV-stable than UB.
  5. Apply about 1-2 coats with about 30-60 minutes flash-off between coats.
  6. Allow about 24 hours to cure fully so the tough, slightly flexible film can resist stone chipping and road salt.
  7. Inspect annually, especially leading edges and high-impact zones, and touch up as needed.

다른 이름: 빌트햄버, 빌트, 빌트함버, bilt, Dynax-UC, DynaxUC, Dynax UC, Dynax Underbody Clear, BH Dynax-UC, 다이낙스 UC, 빌트햄버 다이낙스-UC, 하부 방청 왁스, 투명 언더보디 왁스

View in English

출처

관련 제품

Bilt Hamber의 다른 제품

같은 카테고리(Coating) 제품

더 보기