PHOBIC - Spray Coating
포빅 스프레이 코팅
PHOBIC Spray Coating delivers ceramic-coating performance in an easy spray format. It uses high-solids chemistry and next-generation silazane resins shared with the Armour Quartz line to form a slick, hydrophobic barrier on paint, trim, plastics, and glass. Durability runs up to about 2 years and PHOBIC can be used on its own or as a topper on existing coatings.
PHOBIC 스프레이 코팅은 세라믹 코팅의 성능을 손쉬운 스프레이 형태로 풀어낸 제품입니다. Armour 쿼츠 라인과 공유하는 고농도 화학과 차세대 실라잔 수지를 사용해 도장·트림·플라스틱·유리에 매끄럽고 발수성 있는 보호막을 형성합니다. 약 2년의 내구성을 제공하며 단독 사용 또는 기존 코팅 위 토퍼로 사용할 수 있습니다.
- Brand
- Armour Detail Supply
- Categories
- Exterior : Coating
- pH
- acid (4.9)
Key features
- Easy spray-on ceramic coating
- High-solids silazane resin chemistry
- Slick hydrophobic barrier
- Works on paint, trim, plastics, and glass
- Up to about 2 years of durability
- Strong chemical resistance
- Standalone or coating topper
Usage
- Decontaminate the vehicle with Armour Decon Soap and Iron Remover, then use a clay bar or synthetic clay mitt for any embedded contamination.
- If swirls or scratches are present, polish the paint to reduce defects and bring up gloss.
- Wipe the surface with Armour Panel Prep, repeating twice when polishing was skipped.
- Prime the applicator or short-nap towel with 10-15 sprays to start; later panels only need 3-5 sprays.
- Apply one panel at a time using overlapping circles and let the product set up about 30-60 seconds until small sweat beads or a light haze form.
- Level with a plush towel in similar circular motions, checking for streaks or cloudy/dark high spots and repeating per panel.
- Move to a fresh side of the leveling towel every other panel; the application towel can run across the whole vehicle.
- If layering, leave a few minutes between coats; PHOBIC is built as a single layer but can be layered when desired.
- After use, remove the spray pump and rinse it with water or alcohol, then secure the cap and store the bottle in a cool, dry place.
- Allow at least 4 hours of initial cure; AMPLIFY or Ceramic Spray Sealant can be added afterward, and avoid washes or chemicals for 24 hours.
핵심 특징
- 손쉬운 스프레이형 세라믹 코팅
- 고농도 실라잔 수지 화학
- 매끄러운 발수 보호막
- 도장·트림·플라스틱·유리에 사용
- 약 2년 내구성
- 강한 내화학성
- 단독 또는 코팅 토퍼로 사용
사용법
- Armour 디콘 솝과 아이언 리무버로 차량을 디컨한 뒤 클레이바 또는 합성 클레이 미트로 잔존 고착 오염을 제거합니다.
- 스월이나 스크래치가 있으면 폴리싱으로 결함을 줄이고 광택을 끌어올립니다.
- Armour 패널 프렙으로 표면을 닦고, 폴리싱을 하지 않았다면 두 번 반복합니다.
- 어플리케이터나 숏냅 타월에 처음에는 10-15회 분사해 프라이밍하고 이후 패널에는 3-5회 분사로 충분합니다.
- 한 패널씩 겹치는 원형 모션으로 도포한 뒤 약 30-60초 셋업해 작은 땀방울이나 옅은 헤이즈가 올라올 때까지 기다립니다.
- 플러시 타월로 같은 원형 모션을 그리며 레벨링하고 흐리거나 어두운 하이스팟·스트릭이 없는지 확인하며 패널마다 반복합니다.
- 두 패널마다 레벨링 타월의 새 면을 사용하고, 어플리케이션 타월·패드는 차량 전체에 계속 사용할 수 있습니다.
- 레이어링 시 각 레이어 사이에 수 분 간격을 둡니다. PHOBIC은 단일 레이어 코팅이지만 다층 도포도 가능합니다.
- 작업이 끝나면 스프레이 펌프를 분리해 물 또는 알코올로 헹구고 캡을 단단히 닫아 서늘하고 건조한 곳에 보관합니다.
- 최소 4시간 초기 경화 후 AMPLIFY나 세라믹 스프레이 실런트를 추가로 올릴 수 있으며, 24시간 동안은 세차나 케미컬 노출을 피합니다.