Glass Coating
글래스 코팅
Armour Glass Coating is a hydrophobic window coating that resists water, rain, and precipitation. Water sheets off starting around 30 mph so wipers can stay off at highway speed, and the coating is rated for up to about 2 years on windshields and 3 or more years on side and rear glass, holding up to roughly 80,000 wiper swipes. It is safe on tempered and laminated glass.
Armour 글래스 코팅은 물·비·강수에 강한 발수성 윈도우 코팅으로, 시속 30마일 부근부터 물이 흘러내려 고속 주행 시 와이퍼 사용을 줄일 수 있습니다. 앞유리에서는 약 2년, 사이드·리어 글래스에서는 3년 이상 지속되며 와이퍼 약 8만 회 작동까지 견디도록 설계되었습니다. 템퍼드 및 라미네이트 글래스 모두에 안전합니다.
- Brand
- Armour Detail Supply
- Categories
- Exterior : Glass Sealant
Key features
- Hydrophobic glass coating
- Water sheeting begins around 30 mph
- Up to about 2 years on windshields
- 3+ years on side and rear glass
- Withstands roughly 80,000 wiper swipes
- Safe on tempered and laminated glass
- Includes 30 ml dropper bottle, mini microfiber applicator pad, instruction card
Usage
- Decontaminate the glass with Armour Decon Soap and Iron Remover, then lift any remaining contamination with a clay bar or synthetic clay mitt.
- Polish the glass to remove any older repellent coatings and promote bonding when possible.
- Wipe with Armour Panel Prep to clear polishing oils and residue, repeating twice when polishing was skipped.
- Prime the applicator with three lines of coating to start; later sections only need a small amount.
- Apply in methodical circular motions with medium to heavy pressure, working half of the windshield or two side panels at a time before leveling.
- Level 95 percent or more on the first wipe with a short-nap pearl-weave towel.
- Switch to a plush towel for final leveling and buff out any streaks or cloudy/dark high spots, repeating per glass section.
- Two layers are recommended on the windshield; layers can be applied immediately or after a wait.
- No cure time is required and the vehicle can be driven and exposed to water right away.
핵심 특징
- 발수성 글래스 코팅
- 약 시속 30마일부터 물 시팅
- 앞유리 약 2년 보호
- 사이드·리어 글래스 3년 이상 보호
- 와이퍼 약 8만 회 작동에 견딤
- 템퍼드·라미네이트 글래스에 안전
- 30ml 드로퍼 보틀, 미니 마이크로파이버 어플리케이터 패드, 사용 설명 카드 포함
사용법
- Armour 디콘 솝과 아이언 리무버로 유리를 디컨한 뒤 클레이 바 또는 합성 클레이 미트로 잔여 고착 오염물을 제거합니다.
- 가능하면 유리를 폴리싱해 기존 발수 코팅을 제거하고 본딩이 잘 되도록 준비합니다.
- Armour 패널 프렙으로 폴리싱 오일과 잔여물을 닦고, 폴리싱을 하지 않았다면 두 번 반복합니다.
- 어플리케이터를 3줄 도포로 프라이밍하고 이후 섹션은 소량만 추가합니다.
- 중간~강한 압력으로 원을 그리며 도포하고, 앞유리 절반 또는 사이드 글래스 2장씩 작업한 뒤 레벨링으로 진행합니다.
- 숏냅 펄 위브 타월로 1차 와이프에서 95% 이상 레벨링합니다.
- 플러시 타월로 최종 레벨링하고 흐리거나 어두운 하이스팟·스트릭을 버프 아웃하며 모든 섹션에서 반복합니다.
- 앞유리는 2겹 도포를 권장하며, 레이어는 즉시 또는 시간 간격을 두고 적용할 수 있습니다.
- 별도의 경화 시간이 필요 없어 즉시 주행과 물 노출이 가능합니다.