PAICAR 03 파인 컷 희석비 & 사용 가이드

PAICAR 03 파인 컷 희석비 pH 스펙 카드

03 Fine Cut

03 파인 컷은 이전 컴파운드 단계에서 남은 가벼운 스월 마크, 미세 스크래치, 홀로그램과 P3000~P4000 샌딩 자국을 정리하는 수성 파인 마무리 폴리시입니다. 실리콘과 필러가 없어 먼지 없이 깔끔하게 버핑되고 쉽게 닦이며 색 깊이와 자연스러운 광택을 되살립니다. 투명한 결과라 코팅 전 검사에 적합합니다.

브랜드
PAICAR
카테고리
Exterior : Polishes
기본 희석 비율
RTU
최종 업데이트
2026-06-02

핵심 특징

희석 비율

용도희석비율
Exterior : Polishes (기본)RTU1:0

사용법

  1. 표면을 세차하고 필요하면 클레이 바로 완전히 오염을 제거한 뒤 패널을 완전히 건조시킵니다.
  2. 제어력과 깊이를 위해 듀얼 액션 폴리셔에 부드럽거나 중간 경도의 폼 패드를 사용합니다.
  3. 잘 흔든 뒤 패드에 3~4방울을 떨어뜨리고 기계를 끈 상태에서 PAICAR 03을 패널에 펴 발라줍니다.
  4. 최저 속도로 시작해 4500rpm까지 올리고, 약 40×60cm 구역을 패드를 평평히 한 채 가볍고 일정한 압력으로 교차 패스합니다.
  5. 3~4회 패스(약 2분) 후 깨끗한 마이크로파이버 타올로 잔여물을 닦고 검사등으로 홀로그램과 미세 스크래치를 확인합니다.
  6. 마감이 만족스러우면 실란트, 왁스 또는 코팅을 도포해 보호하고 마무리합니다.

03 Fine Cut is a water-based fine finishing polish that clears light swirl marks, micro-scratches and leftover holograms from earlier compounding stages, along with P3000 to P4000 sanding marks. Free of silicones and fillers, it buffs cleanly with no dust and wipes off easily while bringing back color depth and natural gloss. Its transparent result suits pre-coating inspection.

Key features

  • Clears light swirl marks, micro-scratches and leftover holograms
  • Removes P3000 to P4000 sanding marks
  • Restores color depth and natural gloss
  • Water-based, dust-free and residue-free
  • Silicone- and filler-free for accurate pre-coating inspection
  • Wipes off without streaks
  • Cut level 6/10, finish level 9/10

Usage

  1. Wash and fully decontaminate the surface, using a clay bar if needed, then dry the panel completely.
  2. Use a soft or medium foam pad on a dual action polisher for more control and depth.
  3. Shake well, apply 3 to 4 drops to the pad, and spread PAICAR 03 over the panel with the machine off.
  4. Start at the lowest speed, then raise up to 4500 rpm, working cross-hatch passes over roughly 40 by 60 cm with light, steady pressure and the pad flat.
  5. After 3 to 4 passes (about 2 minutes), wipe residue with a clean microfiber towel and check holograms and micro-scratches under an inspection light.
  6. Once the finish is right, apply a sealant, wax or coating to protect and enhance it.

다른 이름: PAI, 파이카, 파이, PAICAR 03 Fine Cut, FC, PAICAR FC, 파이카 03 파인 컷, 파이카 FC

View in English

출처

관련 제품

PAICAR의 다른 제품

같은 카테고리(Polishes) 제품

더 보기