리부트젤 고점도
REBOOT-GEL High Viscosity
습식 시공 전용으로 제작된 고점도 젤 타입 실리카 스케일 제거제로, DIY 사용자에게 특히 권장됩니다. 로션에 가까운 초저마찰 점도 덕분에 시공 스크래치를 거의 발생시키지 않으면서 실리카 스케일 및 각종 오염물을 제거할 수 있습니다. 물을 많이 사용해도 성분이 흘러내리지 않아 건조로 인한 케미컬 데미지 위험을 크게 줄였습니다.
- 브랜드
- Ganbass
- 카테고리
- Exterior : Remover
- 기본 희석 비율
- RTU
- pH
- acid
핵심 특징
- 초저마찰 젤 포뮬러로 시공 스크래치 최소화
- 습식 시공 전용 설계
- 일반 REBOOT와 동등한 실리카 스케일 제거력
- 물에 의한 희석 저항 — 성분이 도장면에 잔류
- 섬세하거나 짙은 색 도장의 DIY 사용자에게 권장
- 백색 줄무늬 발생 시 하지 처리 부족 신호로 활용 가능
희석 비율
- Exterior : Remover — RTU (1:0) (기본)
사용법
- 산성 케미컬이므로 사용 전 반드시 고무장갑 등 보호구를 착용하세요.
- 눈에 띄지 않는 부위에서 호환성 테스트를 먼저 실시하세요.
- 7×7cm 정도로 자른 마이크로파이버 클로스에 젤을 충분히 묻혀 도장면에 소면적씩 나누어 도포하세요.
- 젤이 건조되기 전에 물기를 꼭 짠 젖은 클로스로 닦아낸 후 건조 클로스로 마무리하여 스케일 제거 여부를 확인하세요.
- 마지막으로 물로 충분히 헹궈 마무리하세요.
- 습식 시공 시 도장면에 소량의 수분이 남은 상태에서 작업하거나 분무기로 수분을 조절하며 시공하세요.
A high-viscosity gel-type silica scale remover formulated exclusively for wet-surface application, and specifically recommended for DIY users. Its ultra-low-friction lotion-like consistency allows it to remove silica scale and other deposits from paint while generating virtually no application scratches — a critical advantage over conventional acidic chemicals. Designed to stay in place even when water is used generously, dramatically reducing the risk of chemical damage from drying.
Key features
- Ultra-low friction gel formula minimizes application scratches
- Wet-application exclusive design
- Silica scale removal comparable to standard REBOOT
- Resistant to dilution by water — component stays on surface
- Recommended for DIY users on delicate or dark-colored paint
- Acts as a dirt sensor: white streaks indicate inadequate prep
Usage
- Put on rubber gloves before use, as this is an acidic chemical.
- Perform a compatibility test on an inconspicuous area before proceeding.
- Apply a generous amount of gel to a small microfiber cloth (approximately 7 x 7 cm) and spread it onto the paint surface, working in small sections.
- Before the gel dries, wipe it off with a damp wrung cloth, then follow with a dry cloth to check whether the scale has been removed.
- Rinse thoroughly with water to finish.
- For wet application, work on a surface with a small amount of residual water or control moisture with a spray bottle.
다른 이름: 간바스, ganbas, REBOOT-GEL 高粘度, Ganbass REBOOT-GEL 高粘度, Ganbass REBOOT-GEL High Viscosity, 간바스 리부트젤 고점도, REBOOT-GEL-高粘度, Ganbass REBOOT-GEL-高粘度, 간바스 리부트 젤 고점도, 리부트 젤 고점도